Toyota2015–2018Technical specifications

Camry 2.0: Technical specifications

Workshop data for the 2-litre petrol (engine code 6AR-FSE). Covers engine, fluids, brakes, service, torques and air conditioning: the figures to check before a job or a parts order.

Summary

Match the engine code (6AR-FSE) to the vehicle before ordering parts or applying these figures.

Vehicle specifications

Overview

Make: Toyota
Model: Camry
Years: 2015–2018
Fuel: Petrol
Engine code: 6AR-FSE

Performance & efficiency

Power: 110 kW (150 hp)
Engine size: 1,998 cc
Cylinders: 4 · DOHC
Compression ratio: 12.7:1
Fuel system: Toyota

Fluids & capacities

Engine oil (with the filter): 4.4 litres

All 108 specifications below

Engine & identification

Vehicle identification

No. of cylinders Type	4/DOHC
Capacity (Fiscal) cc	1998
Compression ratio :1	12,7
Suitable for unleaded petrol	Yes
Minimum octane rating RON	91
Ignition system Make	Toyota
Ignition system Type	SFI D-4S
Ignition system Description	Map-DI
Trigger location	Cam/Crankshaft
Fuel system Make	Toyota
Fuel system Type	SFI D-4S
Fuel system Description	MFI-s(i+d)
Air metering Type	Mass/MAP
Combined ignition and fuel ECM	Yes
Diagnostic socket	Yes

Ignition system

Ignition coil supply voltage + with ballast V	12,0

Firing order

The firing order for the Toyota Camry 2.0 (2015–2018) is 1-3-4-2.

Firing order	1-3-4-2

Valve clearances

Valve clearances on the Toyota Camry 2.0 (2015–2018) are hydraulic — they self-adjust, so no manual clearance figure applies.

Valve clearance - INLET mm	Hydraulic
Valve clearance - EXHAUST mm	Hydraulic

Engine oil & fluids

Engine oil

The Toyota Camry 2.0 (2015–2018) takes 4.4 litres of engine oil with the filter.

See the reference table for the complete engine oil entries and their conditions.

Coolant

The listed total cooling-system capacity is 7.3 litres.

See the reference table for the complete coolant entries and their conditions.

Grades, filling conditions and capacities

Lubricants and capacities — complete reference
Engine oil options
Ambient temperature range	All temperatures
Engine oil grade SAE	0W-20, 5W-20
Engine oil classification API/ACEA	SL/A3
Ambient temperature range	All temperatures
Engine oil grade SAE	5W-30
Engine oil classification API/ACEA	SL/A3
Ambient temperature range	-18°C➞
Engine oil grade SAE	10W-30
Engine oil classification API/ACEA	SL/A3
Ambient temperature range	-12°C➞
Engine oil grade SAE	15W-40
Engine oil classification API/ACEA	SL/A3
Engine with filter(s) litres	4.4
Other lubricants and capacities
Automatic transmission fluid Type	Toyota ATF WS
Automatic transmission (drain & refill) litres	—
View more information	—
If 'D' shift indicator flashes (transmission fluid temperature is above 45°C): Switch ignition OFF. Allow transmission fluid to cool, then repeat steps 2-7.
Automatic transmission (dry fill) litres	6.7
Automatic transmission fluid
Coolant Type	Toyota SLLC
Coolant Colour	Pink
Cooling system - total capacity litres	7.3
Brake fluid Type	DOT 3

Brakes & wear limits

Brake disc thickness

Brake discs on the Toyota Camry 2.0 (2015–2018) are replaced at a minimum thickness of 25 mm (ventilated) front and 8,5 mm rear.

Minimum disc thickness for replacement - ventilated Front	25 mm
Minimum disc thickness for replacement Rear	8,5 mm
Maximum drum diameter for replacement Rear	171 mm

Brake disc and drum dimensions

Disc runout Front	0,05 mm
Disc runout Rear	0,15 mm
Minimum pad thickness Front	1 mm
Minimum pad thickness Rear	1 mm
Minimum shoe thickness Rear	1 mm
Parking brake travel No. of notches	7-10

Service & electrical

Tuning and emissions

Ignition timing - basic BTDC °Engine/rpm	10±2/650±50 Not adjustable
Ignition advance checks °Engine/rpm	ECM Controlled
Idle speed rpm	650±50 Not adjustable
Oil temperature °C	80
CO level at idle speed - tailpipe Vol. % CO	0,2 Max Not adjustable
HC level at idle speed ppm	100
CO2 level at idle speed Vol. % CO2	14,5-16
O2 level at idle speed Vol. % O2	0,1
Increased idle speed for CO test rpm	2300-2700
CO content at increased idle speed Vol. %	0,2
Lambda at increased idle λ	0,97-1,03

Starting and charging

Alternator output A/V/rpm	30/13,2-14,8/2000

Service checks and adjustments

Oil pressure
Compression pressure bar	9,8-14,0
Oil pressure bar/rpm	—
Radiator cap bar	0,79-1,23
Thermostat opens °C	80-84

Fuel system

Injector resistance
Fuel feed/lift pump delivery pressure bar	1,9-5,9
Fuel main pump delivery pressure bar	35-45
Engine coolant temperature (ECT) sensor Ohm/°C	310-326/80
Injector Ohm	11,6-12,4/20°C
Lambda sensor (Oxygen) heater Ohm	9,0-14,0
Throttle motor Ohm	0,3-100

Spark plugs

Spark plugs Original equipment	Denso
Spark plug Type	FK16HBR-J8
Electrode gap mm	0,7-0,8

Tightening torques

Other engine tightening torques
Cylinder head instructions	—
View more information	—
Main bearings Stage 1	—
View more information	—
Main bearings
Big end bearings Renew bolts/nuts	—
View more information	—
Big end bearings
Big end bearings Stage 1	40 Nm
Big end bearings Stage 2	90°
Sump bolts	—
View more information	—
Wait 2 hours before starting engine or filling engine with oil to allow sealant to dry.
Sump drain bolt	40 Nm
Flywheel/driveplate	-/98 Nm
After installing driveplate wait 1 hour before starting engine.
Crankshaft pulley/damper centre bolt	260 Nm
Camshaft sprocket/gear	—
View more information	—
Exhaust camshaft sprocket
Camshaft carrier/cap	—
View more information	—
If hydraulic tappets were removed, 50 ml of oil must be added into oil hole fig132869 . Make sure the oil passage is full of oil.
Camshaft/rocker cover	—
View more information	—
Bolts 1, 2, 3, 4, 5 are tightened twice (20, 21, 22, 12, 19).
Inlet manifold to cylinder head	28 Nm
Exhaust manifold to cylinder head	62 Nm
Spark plugs	25 Nm
Fuel rail	21 Nm
Fuel rail
Crankshaft position (CKP) sensor/engine speed (RPM) sensor	7 Nm
Camshaft position (CMP) sensor	10 Nm
Engine coolant temperature (ECT) sensor	20 Nm
Lambda sensor (Oxygen)	44 Nm
Knock sensor (KS)	20 Nm
Engine oil pressure switch	15 Nm
Assemble components within 3 minutes. Do not start engine for 1 hour.
Oil filter	25 Nm
Chassis tightening torques
Front hub	294 Nm
Rear hub - wheel bearing housing bolts	80 Nm
Steering wheel	50 Nm
Steering rack/box mounting	70 Nm
Steering track rod end	49 Nm
Steering track rod end
Brake caliper to carrier Front	34 Nm
Brake caliper/carrier to hub Front	107 Nm
Brake caliper to carrier Rear	27 Nm
Brake caliper/carrier to hub Rear	62 Nm
ABS sensor Front	9 Nm
Road wheels	103 Nm

Air conditioning

No. of AC service connectors	2
Air conditioning restrictor type	Expansion valve
Compressor clutch/magnetic coupling	Yes
Compressor variable displacement solenoid	Yes
Air conditioning refrigerant Type	R134a
Air conditioning refrigerant quantity grams	500±50
Air conditioning oil group	PAG
Air conditioning oil Type	Dens Oil 8
Air conditioning oil quantity cm³	100+15
Air conditioning oil viscosity ISO	46

Frequently asked questions

What is the firing order of the Toyota Camry 2.0?

The firing order for the Toyota Camry 2.0 (2015–2018) is 1-3-4-2.

How much oil does the Toyota Camry 2.0 take?

The Toyota Camry 2.0 (2015–2018) takes 4.4 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.

What are the valve clearances for the Toyota Camry 2.0?

Valve clearances on the Toyota Camry 2.0 (2015–2018) are hydraulic — they self-adjust, so no manual clearance figure applies.

What is the minimum brake disc thickness for the Toyota Camry 2.0?

Brake discs on the Toyota Camry 2.0 (2015–2018) are replaced at a minimum thickness of 25 mm (ventilated) front and 8,5 mm rear.