Toyota1984–1986Technical specifications

Camry 2.0: Technical specifications

Workshop data for the 2-litre petrol (engine code 2S-E). Covers engine, fluids, service and torques: the figures to check before a job or a parts order.

Summary

Match the engine code (2S-E) to the vehicle before ordering parts or applying these figures.

Vehicle specifications

Overview

Make: Toyota
Model: Camry
Years: 1984–1986
Fuel: Petrol
Engine code: 2S-E

Performance & efficiency

Power: 79 kW (107 hp)
Engine size: 1,995 cc
Cylinders: 4 · OHC
Compression ratio: 9.0:1
Fuel system: Toyota

Fluids & capacities

Engine oil (with the filter): 4.0 litres

All 93 specifications below

Engine & identification

Vehicle identification

No. of cylinders Type	4/OHC
Capacity (Fiscal) cc	1995 (1981)
Compression ratio :1	9,0
Suitable for unleaded petrol	Yes
Minimum octane rating RON	98/95
Ignition system Type	TSZ-i
Ignition system Description	Trans-i
Fuel system Make	Toyota
Fuel system Type	EFI
Fuel system Description	MFI-i

Ignition system

Ignition coil Make	Denso
Ignition coil supply voltage + with ballast V	12,0
Primary resistance Ohm	0,38-0,46
Secondary resistance Ohm	7700-10400
Distributor (ECM) Make	Denso
Distributor (ECM) No.	74060
Contact breaker gap/trigger air gap mm	0,2-0,4

Firing order

The firing order for the Toyota Camry 2.0 (1984–1986) is 1-3-4-2.

Firing order	1-3-4-2

Valve clearances

Valve clearances on the Toyota Camry 2.0 (1984–1986) are hydraulic — they self-adjust, so no manual clearance figure applies.

Valve clearance - INLET mm	Hydraulic
Valve clearance - EXHAUST mm	Hydraulic

Engine oil & fluids

Engine oil

The Toyota Camry 2.0 (1984–1986) takes 4.0 litres of engine oil with the filter.

A listed engine oil option is SAE 10W-30 for moderate climates, with API/ACEA classification SE.

A listed engine oil option is SAE 20W-50 as an alternative for moderate climates.

Manual gearbox

The manual gearbox has a listed capacity of 2.6 litres. The specified oil is Dexron II.

Coolant

The listed total cooling-system capacity is 7.0 litres.

Grades, filling conditions and capacities

Lubricants and capacities — complete reference
Engine oil options
Ambient temperature range	Moderate climate
Engine oil grade SAE	10W-30
Engine oil classification API/ACEA	SE
Ambient temperature range	Moderate climate alternative
Engine oil grade SAE	20W-50
Engine with filter(s) litres	4.0
Other lubricants and capacities
Manual transmission oil grade SAE	Dexron II
Manual transmission litres	2.6
Automatic transmission fluid Type	Dexron II
Automatic transmission (drain & refill) litres	2.5
Differential oil grade - front SAE	Dexron II
Differential front/AT litres	AT=1,6
Cooling system - total capacity litres	7.0

Service & electrical

Ignition timing

Basic ignition timing for the Toyota Camry 2.0 (1984–1986) is 10°±2° BTDC at 750 rpm.

Ignition timing	Without vacuum
Ignition timing - basic BTDC °Engine/rpm	10±2/750
Ignition timing - alternative °Engine/rpm	95=8±2/750

Battery

The Toyota Camry 2.0 (1984–1986) uses a 12 V, 60 Ah battery (reserve capacity 90 minutes).

Battery V/RC(Ah)	12/90 (60)

Spark plugs

The Toyota Camry 2.0 (1984–1986) uses NGK BPR5EY-11 spark plugs with a 1,1 mm electrode gap.

Spark plugs Original equipment	NGK
Spark plug Type	BPR5EY-11
Electrode gap mm	1,1
Spark plugs Make	Bosch
Spark plug Type	WR8DCX
Electrode gap mm	1,1
Spark plugs Make	Champion
Spark plug Type	RN9YCC4
Electrode gap mm	1,1
Spark plugs Make	NGK
Spark plug Type	BPR5EY-11
Electrode gap mm	1,1

Tuning and emissions

Ignition advance	Without vacuum and basic timing
Ignition advance checks °Engine/rpm	0-1/1000
Ignition advance checks °Engine/rpm	12/2200
Ignition advance checks °Engine/rpm	17/6000
Vacuum check	Ignition timing advances
Vacuum range °Engine	6-18
Vacuum starts mbar	107
Vacuum ends mbar	667
Idle speed rpm	600-750
Idle speed - alternative rpm	AT=700-850
Fast idle speed - MT/AT rpm	3000
Oil temperature °C	60-80
CO level at idle speed - tailpipe Vol. % CO	1,0±0,5
HC level at idle speed ppm	300
CO2 level at idle speed Vol. % CO2	13-16
O2 level at idle speed Vol. % O2	0,5-2,0

Starting and charging

Starter motor Make	Denso
Starter motor Type	12V 1,0-1,4 kW
Minimum starting voltage V	11,0
Maximum cranking amps A	162-198
Alternator Make	Nippon Denso
Alternator Type	60A
Alternator output A/V/rpm	60/14/2500
Regulated voltage V	13,5-14,3

Service checks and adjustments

Compression pressure bar	9,0-12,5
Oil pressure bar/rpm	2,5-5,0/3000
Radiator cap bar	0,75-1,05
Thermostat opens °C	80-84
Drive belt size - alternator mm	5PKx1000

Fuel system

System pressure bar	2,3-2,7
Regulated pressure with vacuum bar	2,0

Tightening torques

Cylinder head bolt torque

The cylinder head bolts on the Toyota Camry 2.0 (1984–1986) are tightened in 3 stages: 20-30 Nm, then 30-40 Nm, then a final 60-70 Nm.

Cylinder head
Tighten	20-30 Nm
Tighten	30-40 Nm
Tighten	60-70 Nm

Other engine tightening torques
Cylinder head instructions	—
Main bearings Stage 1	27-33 Nm
Main bearings Stage 2	54-66 Nm
Big end bearings Stage 1	22-27 Nm
Big end bearings Stage 2	45-55 Nm
Flywheel/driveplate	88-93 Nm/83 Nm
Crankshaft pulley/damper centre bolt	108 Nm
Spark plugs	15-20 Nm
Chassis tightening torques
Front hub	185 Nm
Rear hub	120 Nm
Road wheels	105 Nm

Frequently asked questions

What is the firing order of the Toyota Camry 2.0?

The firing order for the Toyota Camry 2.0 (1984–1986) is 1-3-4-2.

What spark plugs does the Toyota Camry 2.0 use?

The Toyota Camry 2.0 (1984–1986) uses NGK BPR5EY-11 spark plugs with a 1,1 mm electrode gap.

How much oil does the Toyota Camry 2.0 take?

The Toyota Camry 2.0 (1984–1986) takes 4.0 litres of engine oil with the filter. A listed engine oil option is SAE 10W-30 for moderate climates, with API/ACEA classification SE. A listed engine oil option is SAE 20W-50 as an alternative for moderate climates.

What are the valve clearances for the Toyota Camry 2.0?

Valve clearances on the Toyota Camry 2.0 (1984–1986) are hydraulic — they self-adjust, so no manual clearance figure applies.

What is the cylinder head torque for the Toyota Camry 2.0?

The cylinder head bolts on the Toyota Camry 2.0 (1984–1986) are tightened in 3 stages: 20-30 Nm, then 30-40 Nm, then a final 60-70 Nm.

What is the ignition timing for the Toyota Camry 2.0?

Basic ignition timing for the Toyota Camry 2.0 (1984–1986) is 10°±2° BTDC at 750 rpm.