Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity cc | 1910 |
| Compression ratio :1 | 17,5 |
| Fuel system Make | Bosch |
| Fuel system Type | EDC 16C8 |
Injection system
| Air metering Type | Mass |
|---|---|
| Fuel/injection pump assembly Make | Bosch |
| Pump type | Common rail |
| Fuel feed/lift pump delivery pressure bar | 2,0-3,0 |
Injection sequence
The injection sequence for the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) is 1-3-4-2.
| Injection sequence | 1-3-4-2 |
|---|
Valve clearances
Valve clearances on the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) are hydraulic — they self-adjust, so no manual clearance figure applies.
| Valve clearance - INLET mm | Hydraulic |
|---|---|
| Valve clearance - EXHAUST mm | Hydraulic |
Engine oil & fluids
Engine oil
The Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) takes 4.4 litres of engine oil with the filter.
See the reference table for the complete engine oil entries and their conditions.
Manual gearbox
The manual gearbox has a listed capacity of 2.0 litres. The specified oil is SAE 75W-80 synthetic, with classification GL-5.
Coolant
The listed total cooling-system capacity is 7.2 litres.
See the reference table for the complete coolant entries and their conditions.
Grades, filling conditions and capacities
| Engine oil options | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-40 Synthetic |
| Engine oil classification OEM | Fiat 9.55535-Z2 |
| Engine oil classification API/ACEA | CF |
| Engine with filter(s) litres | 4.4 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | 75W-80 Synthetic |
| Manual transmission oil classification | GL-5 |
| Manual transmission litres | 2.0 |
| Coolant Type | Paraflu 11 |
| Coolant Colour | Green Blue |
| Cooling system - total capacity litres | 7.2 |
| Brake fluid Type | DOT 4 |
| Brake fluid litres | 0.5 |
| Clutch fluid Type | DOT 4 |
| Power steering fluid Type | Dexron II |
| Power steering fluid litres | 1.2 |
Brakes & wear limits
Brake disc thickness
Brake discs on the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) are replaced at a minimum thickness of 20,2 mm (ventilated) or 20,5 mm (ventilated) front and 9 mm or 9,35 mm rear.
| Minimum disc thickness for replacement - ventilated Front | 20,2 mm |
|---|---|
| Minimum disc thickness after refacing - ventilated Front | 20,5 mm |
| Minimum disc thickness for replacement Rear | 9 mm |
| Minimum disc thickness after refacing Rear | 9,35 mm |
Service & electrical
Tuning and emissions
| Idle speed rpm | 850±20 |
|---|---|
| Oil temperature °C | 80 |
| Maximum time at governed speed secs | 1,0 |
| Test mode A/B | B |
| Probe type 1/2 | 1 |
| Smoke opacity - EU limit m-1 (%) | 1,50 (47) |
| Smoke opacity - homologation value m-1 (%) | 0,52 (20) |
Starting and charging
| Battery V/RC(Ah) | 12 |
|---|
Service checks and adjustments
| Radiator cap bar | 0,98 |
|---|---|
| Thermostat opens °C | 86-90 |
Tightening torques
Cylinder head bolt torque
The cylinder head bolts on the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) are tightened in 5 stages: 20 Nm, then 65 Nm, then 90°, then 90°, then a final 90°.
| Cylinder head | |
|---|---|
| Renew bolts | Yes |
| Tighten | 20 Nm |
| Tighten | 65 Nm |
| Tighten | 90° |
| Tighten | 90° |
| Tighten | 90° |
| Cylinder head instructions | — |
|---|---|
| Other engine tightening torques | |
| Sump bolts | — |
| Sump bolts | |
| Sump drain bolt | 50±5 Nm |
| Flywheel/driveplate | 160±16 Nm/- |
| Clutch pressure plate | 28±3 Nm |
| Crankshaft pulley/damper centre bolt | 340±17 Nm |
| Crankshaft pulley/damper bolts | 26±2 Nm |
| Camshaft sprocket/gear | 120±12 Nm |
| Injector/clamp | 26±2 Nm |
| Injector pipe unions | 23±1 Nm |
| Fuel/injection pump sprocket/gear | 50±5 Nm |
| Fuel/injection pump mounting | 25±2 Nm |
| Glow plugs | 8±1 Nm |
| Chassis tightening torques | |
| Front hub | 71±3 Nm+62°±2° |
| Front hub - wheel bearing housing bolts | 80±4 Nm |
| Rear hub | 320±16 Nm |
| Steering rack/box mounting | 130±13 Nm |
| Steering track rod end | 36±3 Nm |
| Brake disc to hub Front | 12±2 Nm |
| Brake caliper to carrier Front | 52±6 Nm |
| Brake caliper/carrier to hub Front | 117±6 Nm |
| Brake disc to hub Rear | 12±2 Nm |
| Brake caliper to carrier Rear | 50 Nm |
| Brake caliper/carrier to hub Rear | 50±5 Nm |
| ABS sensor Front | 8±1 Nm |
| ABS sensor Rear | 8±1 Nm |
| Road wheels | 98 Nm Alu=120 Nm |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | No |
| Air conditioning refrigerant Type | R134a |
Frequently asked questions
What is the injection sequence of the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse?
The injection sequence for the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) is 1-3-4-2.
How much oil does the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse take?
The Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) takes 4.4 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.
What are the valve clearances for the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse?
Valve clearances on the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) are hydraulic — they self-adjust, so no manual clearance figure applies.
What is the cylinder head torque for the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse?
The cylinder head bolts on the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) are tightened in 5 stages: 20 Nm, then 65 Nm, then 90°, then 90°, then a final 90°.
What is the minimum brake disc thickness for the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse?
Brake discs on the Alfa Romeo 147 1.9 JTDM 16V Ducati Corse (2008–2010) are replaced at a minimum thickness of 20,2 mm (ventilated) or 20,5 mm (ventilated) front and 9 mm or 9,35 mm rear.