25 documented faults
Engine & fuel system
5 documented faults — symptoms, causes and workshop fixes.
Low engine coolant level warning displayed.
All models with 2.2 Diesel engine.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Fit new exhaust gas recirculation (EGR) cooler.
Data: Motorwise Workshop. Bulletin 7.
Warning message 'Restricted performance' displayed in instrument panel.
All models with 2.2 Diesel engine, 2014-16.
What you'd notice
Trouble code stored in engine control module (ECM) fault memory: P244A.
The repair
Diesel particulate filter (DPF) pressure sensor faulty.
Workshop instructions & parts1 part
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Fit new Diesel particulate filter (DPF) pressure sensor. Carry out Diesel particulate filter (DPF) pressure sensor calibration using diagnostic equipment.
| Part | Part number | Qty |
|---|---|---|
| Diesel particulate filter (DPF) pressure sensor | LR071398 | 1 |
Data: Motorwise Workshop. Bulletin 9.
Erratic idle at normal operating temperature.
All models with Diesel engines, 2012→.
What you'd notice
Engine misfire/hesitation on idle.
The repair
Engine control module (ECM) software fault causing fuel pressure fluctuations.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program engine control module (ECM) with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
Data: Motorwise Workshop. Bulletin 12.
Loss of engine power. Engine malfunction indicator lamp (MIL) illuminated.
All models with DW12CTED4/224DT engine code, 2014-15.
Turbocharger (TC) intercooler hose detached at joint connection.
Workshop instructions & parts1 part
Workshop procedure
- Fit new turbocharger (TC) intercooler hose.
- Ensure turbocharger (TC) intercooler hose and hose clamps are fitted correctly Fig.1230070 .
- Tighten hose clamps to 5 Nm.
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Turbocharger (TC) intercooler hose | LR063944 | 1 |
Data: Motorwise Workshop. Bulletin 15.
Low engine coolant level warning displayed.
All models with 2.2 Diesel engine.
What you'd notice
Loss of coolant.
The repair
Exhaust gas recirculation (EGR) cooler seal failure due to contamination.
Workshop instructions & parts1 part
Workshop procedure
- Inspect exhaust gas recirculation (EGR) cooler seal.
- Unmodified version of exhaust gas recirculation (EGR) cooler seal has two tabs Fig.1262207.1 .
- Fit modified exhaust gas recirculation (EGR) cooler complete with modified seal. Note: Modified exhaust gas recirculation (EGR) cooler seal has one tab Fig.1262207.2 .
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Exhaust gas recirculation (EGR) cooler | LR057662 | 1 |
Data: Motorwise Workshop. Bulletin 22.
Electrical & ignition
3 documented faults — symptoms, causes and workshop fixes.
Intermittent self-activation of alarm system siren.
All models.
What you'd notice
Audible warning sounds when locking vehicle. Bonnet open warning message displayed in instrument panel.
The repair
Bonnet switch faulty.
Workshop instructions & parts1 part
Workshop procedure
- Fit new bonnet switch. Bonnet switch integral to bonnet latch.
| Part | Part number | Qty |
|---|---|---|
| Bonnet switch | LR054331 | 1 |
Data: Motorwise Workshop. Bulletin 6.
Battery discharged after standing overnight.
All models, 2014-16.
What you'd notice
Clicking noise from load area when ignition switched ON. Low battery voltage warning displayed in instrument panel.
The repair
CAN data bus gateway control module does not switch to sleep mode due to software fault.
Workshop instructions
Workshop procedure
- Charge battery if necessary.
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program CAN data bus gateway control module with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
Data: Motorwise Workshop. Bulletin 11.
Front interior lamp illuminates by itself.
All models.
Chafing within front interior lamp assembly causing short circuit.
Workshop instructions & parts1 part
Workshop procedure
- Remove front interior lamp assembly.
- Carefully disassemble front interior lamp assembly.
- Thoroughly clean electrical contact terminals Fig.1238363.1 .
- Fit a rubber sleeve to each electrical contact terminal ensuring 2 - 3 mm clearance at base Fig.1238363.2 .
- Reassemble front interior lamp assembly and refit.
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Rubber sleeve kit | LR060212 | 1 |
Data: Motorwise Workshop. Bulletin 16.
Brakes
2 documented faults — symptoms, causes and workshop fixes.
Squeaking noise from rear brakes.
All models.
Vibration between rear brake pads and discs.
Workshop instructions & parts1 part
Workshop procedure
- Inspect rear brakes for damage and replace if necessary.
- Apply anti-seize grease to contact surfaces of brake pad back plates.
| Part | Part number | Qty |
|---|---|---|
| Anti-seize grease | LR020053 | 1 |
Data: Motorwise Workshop. Bulletin 5.
Irregular operation of stop-start system. Engine does not restart when neutral selected.
All models with 2.2 Diesel engine, →2015.
ABS/ESP control module software fault.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program ABS/ESP control module with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
Data: Motorwise Workshop. Bulletin 20.
Suspension & drivetrain
5 documented faults — symptoms, causes and workshop fixes.
Clicking noise from front suspension when manoeuvring or parking.
All models, →2012.
Contact between front suspension lower arm ball joint and ball joint pinch bolt.
Workshop instructions & parts3 parts
Workshop procedure
- Remove and discard brake caliper lower bolt.
- Mark suspension lower arm ball joint with white paint Fig.1179645.1 .
- Remove and discard pinch bolt and nut from suspension lower arm ball joint.
- Remove suspension lower arm ball joint from front wheel hub.
- Turn suspension lower arm ball joint 90 ° and refit Fig.1179645.2 .
- Fit new pinch bolt and nut for suspension lower arm ball joint.
- Fit new brake caliper lower bolt.
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Bolt | LR000093 | 2 |
| Nut | FY112056 | 2 |
| Bolt | LR024506 | 2 |
Data: Motorwise Workshop. Bulletin 1.
Creaking noise from front suspension when driving over speed humps when ambient air temperature is low.
All models.
Unsatisfactory design of front anti-roll bar bushes.
Workshop instructions & parts1 part
Workshop procedure
- Replace front anti-roll bar bushes.
| Part | Part number | Qty |
|---|---|---|
| Anti-roll bar bush | LR030743 | 2 |
Data: Motorwise Workshop. Bulletin 2.
Noise from rear suspension over speed humps.
All models with active suspension system, 2012-13.
Software fault in suspension control module.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program suspension control module with upgraded software.
Data: Motorwise Workshop. Bulletin 3.
Active suspension system warning lamp illuminated.
All models with active suspension system.
Open circuit/high resistance in wiring harness of active suspension system.
Workshop instructions
Workshop procedure
- Check active suspension system wiring harness for damage and repair/replace as necessary.
Data: Motorwise Workshop. Bulletin 18.
Active suspension system warning lamp illuminated.
All models with active suspension system.
What you'd notice
Trouble codes stored in suspension control module fault memory.
The repair
Damage to front shock absorber wiring harness.
Workshop instructions & parts1 part
Workshop procedure
- Inspect front shock absorber wiring harness for damage.
- If damage to shock absorber wiring harness has occurred within 20 mm from base of front shock absorber Fig.1262234.1 : Fit new front shock absorber.
- If damage to shock absorber wiring harness has occurred after 20 mm from base of front shock absorber: Repair wiring harness using harness repair kit and connectors. Note: Ensure front shock absorber repaired wiring harness total length does not exceed 165 mm Fig.1262234.2 .
- If necessary, repeat procedure for opposite side.
- Erase any stored trouble codes.
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Wiring harness repair kit | LR056270 | 1 |
Data: Motorwise Workshop. Bulletin 23.
Clutch & gearbox
3 documented faults — symptoms, causes and workshop fixes.
Warning message 'Transmission Fault' displayed in instrument panel.
All models with transmission code 9HP48, VIN 815019-989125.
What you'd notice
Trouble codes stored: P0600, P0710, P0712, P0713, P0975, P0978, P0981, P0984, P099B.
The repair
Wiring harness in the transmission not correctly crimped. Transmission control module (TCM) software fault.
Workshop instructions & parts2 parts
Workshop procedure
- Inspect production number on automatic transmission Fig.1217585.1 .
- If production number before 141773: Replace transmission valve block wiring harness. Re-program transmission control module (TCM) with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
| Part | Part number | Qty |
|---|---|---|
| Transmission valve block wiring harness - Diesel | LR064790 | 1 |
| Transmission valve block wiring harness - petrol | LR049888 | 1 |
Data: Motorwise Workshop. Bulletin 8.
Oil leak from transmission.
All models with transmission code 9HP48, 2014→.
What you'd notice
Abnormal noise from transmission. Poor gear shifting.
The repair
Poor manufacture of transmission oil gallery plate gasket.
Workshop instructions & parts3 parts
Workshop procedure
- Remove and discard transmission oil gallery plate gasket and retaining bolts.
- Thoroughly clean all mating surfaces.
- Fit modified transmission oil gallery plate gasket.
- Refit transmission oil gallery plate using new retaining bolts. Tightening torque: 10 Nm. Observe correct transmission oil gallery plate retaining bolt tightening sequence Fig.1217801 .
- Top up transmission oil as required.
| Part | Part number | Qty |
|---|---|---|
| Retaining bolt | Refer to manufacturer | 11 |
| Transmission oil gallery plate gasket | LR086413 | 1 |
| Transmission oil | LR023288 | As required |
Data: Motorwise Workshop. Bulletin 13.
Transmission fluid leak from LH front of vehicle.
All models with 6-speed automatic transmission.
Transmission oil cooler chafed through against bonnet release cable.
Workshop instructions & parts2 parts
Workshop procedure
- Remove and discard bonnet release cable retaining clip Fig.1262200.1 .
- Fit new bonnet release cable retaining clip as shown Fig.1262200.2 .
- Ensure bonnet release cable fitted correctly Fig.1262200.3 .
- Fit new transmission oil cooler.
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Bonnet release cable retaining clip | LR035103 | 1 |
| Transmission oil cooler | LR002916 | 1 |
Data: Motorwise Workshop. Bulletin 24.
Air conditioning & heating
2 documented faults — symptoms, causes and workshop fixes.
Reduced air flow to vehicle interior.
All models with automatic temperature control (ATC), VIN H706084→.
What you'd notice
Evaporator freezes reducing or stopping air flow to vehicle interior. Poor AC/heater blower motor performance.
The repair
Software fault in AC control module.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program AC control module with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
Data: Motorwise Workshop. Bulletin 14.
Air conditioning (AC) inefficient.
All models with air conditioning (AC).
Refrigerant leak from AC service connector.
Workshop instructions
Workshop procedure
- Fit new AC service connector Schrader valve.
- Recharge AC system with correct quantity of refrigerant.
Data: Motorwise Workshop. Bulletin 19.
Wipers & visibility
2 documented faults — symptoms, causes and workshop fixes.
Windscreen wipers intermittent operation or not working.
All models, 2012→.
What you'd notice
Indicators intermittent operation or not working.
The repair
Poor electrical connection between switch assembly and harness multi-plug.
Workshop instructions & parts1 part
Workshop procedure
- Remove windscreen wiper switch.
- Clean windscreen wiper switch harness multi-plug terminals Fig.1217605.1 .
- Lightly coat terminals with grease Fig.1217605.1 . Use specified grease.
- Refit windscreen wiper switch.
- Repeat procedure for indicator switch.
| Part | Part number | Qty |
|---|---|---|
| Electrical contact grease (Nyogel) | LR054614 | 1 |
Data: Motorwise Workshop. Bulletin 10.
Creaking/rattling noise from fascia central area.
All models without head up display.
Fascia and windscreen rubbing together.
Workshop instructions
Workshop procedure
- Cut felt tape to make a strip approximately 3 mm x 15 mm x 55 mm in size.
- Using a suitable tool insert felt strip Fig.1269722.1 between fascia and windscreen (adjacent to central defrost vent).
- Ensure felt strip is not visible from inside car.
- View View more information
Data: Motorwise Workshop. Bulletin 25.
Other
3 documented faults — symptoms, causes and workshop fixes.
Hill hold function activated when manoeuvring or parking.
All models with 6 speed manual transmission, 2012-13.
Incorrect specification rear wheel speed sensors fitted.
Workshop instructions & parts1 part
Workshop procedure
- Fit new rear wheel speed sensors.
| Part | Part number | Qty |
|---|---|---|
| Rear wheel speed sensor | LR024208 | 2 |
Data: Motorwise Workshop. Bulletin 4.
Squeaking/creaking noise from rear of vehicle when driving over rough roads.
All models.
Rear anti-roll bar bushes worn.
Workshop instructions
Workshop procedure
- Replace rear anti-roll bar bushes.
Data: Motorwise Workshop. Bulletin 17.
Squeaking/creaking noise from rear of vehicle when driving over rough roads. Noise more pronounced when ambient air temperature is low.
All models.
Unsatisfactory design of rear anti-roll bar bushes.
Workshop instructions & parts2 parts
Workshop procedure
- Fit modified rear anti-roll bar bushes.
| Part | Part number | Qty |
|---|---|---|
| Anti-roll bar bush | LR113771 | 2 |
| Bolt | RYG500470 | 4 |
Data: Motorwise Workshop. Bulletin 21.
Take it with you
Before you view one
Land Rover Range Rover Evoque 2.2 eD4 (2011–2015)
Each documented fault as a quick check for a viewing or test drive — tick them off as you go.
A little workshop vocabulary
Workshop terms used on this page
Definitions for the technical language used in these bulletins.
- ECM
- Engine control module — the car's engine computer
- VIN
- Vehicle identification number — 17 characters, found at the base of the windscreen and on the V5C logbook
- Nm
- Newton-metres — the standard unit for how tightly a bolt is done up
- EGR
- Exhaust gas recirculation — feeds some exhaust gas back into the intake to cut emissions
- DPF
- Diesel particulate filter — traps soot in the exhaust and burns it off periodically
- Trouble Codes
- Standardised fault codes stored by the engine computer, read with a diagnostic tool
- AC
- Air conditioning — the system that cools the cabin
- ATC
- Automatic temperature control — climate control that holds the temperature you set
- ABS/ESP
- Anti-lock braking and electronic stability programme — the computer that stops the wheels locking and keeps the car stable
- TC
- Turbocharger — the exhaust-driven compressor that boosts engine power
- TCM
- Transmission control module — the gearbox computer
- AC/Heater
- The heating and air-conditioning system
- Anti-Roll Bar
- A bar that links the left and right suspension to cut body roll in corners
- Anti-Seize
- Grease that stops mating parts (like a wheel on a hub) from corroding together
- CAN Data Bus
- The car's internal network that lets control modules talk to each other
- Caliper
- The part that squeezes the brake pads onto the disc
- Control Module
- A computer that runs one of the car's systems (engine, gearbox, brakes, body, and so on)
- Fascia
- The dashboard and the surrounding interior panel
- Fault Memory
- The list of stored trouble codes in a control module
- Instrument Panel
- The dashboard display that shows warning lights and messages
- Multi-Plug
- A multi-pin electrical connector on a wiring harness
- Oil Gallery
- An internal oil passage in the engine
- Refrigerant
- The gas/liquid that carries heat in the air-conditioning system
- Re-Program
- Update the software on a control module using the manufacturer's diagnostic tool
- Trouble Code
- A standardised fault code stored by a control module, read with a diagnostic tool
- Valve Block
- The set of solenoid valves that directs air or fluid in the air-suspension or gearbox
- Wiring Harness
- The bundled cables that carry power and signals around the vehicle
- Blower Motor
- The fan that pushes air through the heater and air-conditioning
- Bonnet Switch
- The switch that tells the alarm whether the bonnet is open
- Bushes
- Rubber mountings that let a suspension or body joint move without metal-to-metal contact
- Calibration
- Setting a sensor or module so its readings match the real world
- Evaporator
- The air-conditioning heat exchanger in the dashboard that cools the cabin air
- Intercooler Hose
- The pipe that carries pressurised air between the turbocharger, intercooler and engine
- Lower Arm
- A suspension link that locates the wheel at the bottom of the hub
- Misfire
- One or more cylinders not firing correctly — the engine runs roughly or loses power
- Recirculation
- Air-conditioning mode that recirculates cabin air instead of drawing in outside air
- Sleep Mode
- The low-power state control modules enter when the car is parked; if one stays awake the battery can go flat
Common questions
Using this guide.
What are the common faults with the Land Rover Range Rover Evoque 2.2 eD4?
Garages and workshops regularly encounter 25 documented faults on the Land Rover Range Rover Evoque 2.2 eD4 — five concern the engine and fuel system and five the suspension and drivetrain. Each fault above lists the symptoms, cause, fix and any parts needed.
Does every Land Rover Range Rover Evoque 2.2 eD4 have these faults?
No. These are patterns documented across the model by workshops, not predictions for an individual car. Where a fault applies only to certain vehicles or VIN ranges, that is listed with the fault.
Can I check for Land Rover Range Rover Evoque 2.2 eD4 faults when viewing one?
Many of them, yes — the documented symptoms are things you can see, hear or feel on a viewing or test drive. The 'Before you view one' checklist above turns each documented fault into a quick check you can tick off as you go.