15 documented faults
Engine & fuel system
4 documented faults — symptoms, causes and workshop fixes.
Poor engine performance.
All models with 2.0 Diesel engine.
What you'd notice
Engine malfunction indicator lamp (MIL) illuminated. Trouble codes stored: P049B, P2453.
The repair
Soot build up in Diesel particulate filter (DPF) due to unsatisfactory design of exhaust gas recirculation (EGR) cooler filter.
Workshop instructions & parts3 parts
Workshop procedure
- Fit modified EGR cooler filter.
- Re-program engine control module (ECM) with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
| Part | Part number | Qty |
|---|---|---|
| EGR cooler filter | LR126126 | 1 |
| Gasket | LR083961 | 1 |
| Gasket | LR095555 | 1 |
Data: Motorwise Workshop. Bulletin 5.
Engine malfunction indicator lamp (MIL) illuminated. Trouble code stored: P0016.
All models with 2.0 Diesel engine except hybrid.
What you'd notice
No loss of engine performance.
The repair
Engine control module (ECM) software fault.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program engine control module (ECM) with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
Data: Motorwise Workshop. Bulletin 8.
Excessive noise from auxiliary drive belt when starting engine.
All models with 2.0 Diesel engine except hybrid.
Unsatisfactory design of crankshaft pulley.
Workshop instructions & parts4 parts
Workshop procedure
- Fit new crankshaft front oil seal. Use special tool: JLR-303-1628 .
- Fit modified crankshaft pulley.
- Fit new crankshaft pulley bolts. Tightening torque: 37 Nm + 90 °. Use special tools: JLR-303-1630 & JLR-303-1686 .
- Fit new auxiliary drive belt.
| Part | Part number | Qty |
|---|---|---|
| Crankshaft pulley | LR115702 | 1 |
| Bolt | LR112877 | 4 |
| Crankshaft front oil seal | LR118109 | 1 |
| Auxiliary drive belt | LR079263 | 1 |
Data: Motorwise Workshop. Bulletin 9.
Engine malfunction indicator lamp (MIL) illuminated. Possible trouble codes stored in engine control module (ECM) fault memory: P229E, P22FE, P22FE, P22A7, P2200.
All models with selective catalytic reduction (SCR) system.
Wiring harness of nitrogen oxide (NOx) sensor chafing on exhaust heat shield.
Workshop instructions & parts3 parts
Workshop procedure
- Inspect wiring harness of nitrogen oxide (NOx) sensor for chafing.
- If wiring harness damaged: Fit new nitrogen oxide (NOx) sensor Fig.1266484.1 . Replace plastic mounting bracket with metal type Fig.1266484.2 .
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Nitrogen oxide (NOx) sensor | LR118316 | 1 |
| Nitrogen oxide (NOx) sensor wiring harness securing clip | LR124847 | 1 |
| Mounting bracket (metal type) | LR106462 | 1 |
Data: Motorwise Workshop. Bulletin 12.
Electrical & ignition
2 documented faults — symptoms, causes and workshop fixes.
Amber Diesel particulate filter (DPF) warning lamp illuminated.
All models with Diesel particulate filter (DPF).
Diesel particulate filter (DPF) blocked due to frequent short journeys or driving at constant low speeds. DPF regeneration process repeatedly not completed.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program engine control module (ECM) with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
- Carry out DPF regeneration using suitable diagnostic equipment.
Data: Motorwise Workshop. Bulletin 6.
When vehicle is approached with keyless entry remote control, tailgate opens unintentionally.
All models with tailgate automatic open/close function.
Tailgate control module wiring harness incorrectly routed.
Workshop instructions
Workshop procedure
- Locate tailgate control module behind LH rear wheel arch lining.
- Check tailgate control module wiring harness for correct routing.
- If tailgate control module wiring harness routing incorrect Fig.1267873.1 : Re-route tailgate control module wiring harness Fig.1267873.2 .
- Repeat procedure for opposite side.
- View View more information
Data: Motorwise Workshop. Bulletin 15.
Brakes
2 documented faults — symptoms, causes and workshop fixes.
Squeal from front brakes when braking lightly.
All models fitted with 325 mm front brake discs, 2015→.
Vibration between brake pads and discs.
Workshop instructions & parts1 part
Workshop procedure
- Fit modified front brake pads.
| Part | Part number | Qty |
|---|---|---|
| Front brake pads | LR094236 | 1 |
Data: Motorwise Workshop. Bulletin 1.
Loss of drive after stop-start system operation.
All models with stop-start system and ZF 9HP48 transmission code.
What you'd notice
Transmission gear position indicator flashes. Warning message 'Reselect gear to manoeuvre' displayed in instrument panel.
The repair
ABS/ESP control module incorrectly programmed.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program ABS/ESP control module with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
Data: Motorwise Workshop. Bulletin 10.
Suspension & drivetrain
2 documented faults — symptoms, causes and workshop fixes.
Knocking noise from front suspension when driving over rough roads or speed humps.
All models, 2015-16.
Front shock absorber protective cap adrift.
Workshop instructions & parts1 part
Workshop procedure
- Lift up shock absorber damper rod cover to gain access to shock absorber protective cap.
- Thoroughly clean area indicated Fig.1228567.1 .
- Apply adhesive to area indicated Fig.1228567.1 .
- Fit shock absorber protective cap into position.
- DO NOT move vehicle for 6 hours to allow adhesive to cure.
- Repeat procedure for opposite side, if necessary.
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Adhesive | LR088285 | 1 |
Data: Motorwise Workshop. Bulletin 4.
Noise from front suspension when driving over rough roads or speed humps.
All models.
Front anti-roll bar making contact with wheel arch lining.
Workshop instructions & parts1 part
Workshop procedure
- Inspect wheel arch lining for signs of contact with front anti-roll bar.
- If contact has occurred: Remove wheel arch lining and discard retaining nuts Fig.1266488.1 . Elongate wheel arch lining hole to make a 7 mm slot Fig.1266488.2 . Modify wheel arch lining by cutting off area indicated Fig.1266488.3 . Fit wheel arch lining using new retaining nuts Fig.1266488.1 . Ensure wheel arch lining is pushed up as far as possible. Caution: All models with active height control suspension. Ensure suspension ride height sensor securing clip positioned in correct hole . Repeat procedure for opposite side.
- View View more information
| Part | Part number | Qty |
|---|---|---|
| Wheel arch lining retaining nut | RYH500780 | 4 |
Data: Motorwise Workshop. Bulletin 13.
Steering
1 documented fault — symptoms, causes and workshop fixes.
Vibration through steering wheel, instrument panel and floor pan at 2400rpm.
All models with 2.0 Diesel engine.
What you'd notice
Noise from under vehicle at 2400rpm.
The repair
Unsatisfactory design of front exhaust mounting bracket.
Workshop instructions & parts1 part
Workshop procedure
- Remove front exhaust mounting bracket from front subframe.
- Remove exhaust heat shield from exhaust mounting bracket.
- Fit heat shield to modified exhaust mounting bracket.
- Fit modified exhaust mounting bracket to front subframe.
| Part | Part number | Qty |
|---|---|---|
| Exhaust mounting bracket | LR107787 | 1 |
Data: Motorwise Workshop. Bulletin 11.
Clutch & gearbox
2 documented faults — symptoms, causes and workshop fixes.
Oil leak from transmission.
All models with transmission code 9HP48, 2014→.
What you'd notice
Abnormal noise from transmission. Poor gear shifting.
The repair
Poor manufacture of transmission oil gallery plate gasket.
Workshop instructions & parts3 parts
Workshop procedure
- Remove and discard transmission oil gallery plate gasket and retaining bolts.
- Thoroughly clean all mating surfaces.
- Fit modified transmission oil gallery plate gasket.
- Refit transmission oil gallery plate using new retaining bolts. Tightening torque: 10 Nm. Observe correct transmission oil gallery plate retaining bolt tightening sequence Fig.1217801 .
- Top up transmission oil as required.
| Part | Part number | Qty |
|---|---|---|
| Retaining bolt | Refer to manufacturer | 11 |
| Transmission oil gallery plate gasket | LR086413 | 1 |
| Transmission oil | LR023288 | As required |
Data: Motorwise Workshop. Bulletin 3.
Warning message 'transmission fault' displayed in instrument panel.
All models with automatic transmission (AT).
What you'd notice
Trouble codes stored in transmission control module (TCM) fault memory: P0933, P0936.
The repair
Wiring harness in the transmission not correctly crimped.
Workshop instructions & parts4 parts
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Fit new transmission valve block wiring harness.
- Re-program transmission control module (TCM) with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
| Part | Part number | Qty |
|---|---|---|
| Transmission valve block wiring harness (petrol) | LR049888 | 1 |
| Transmission valve block wiring harness (Diesel) | LR064790 | 1 |
| Transmission oil | LR023288 | 2 |
| Transmission service kit | LR049876 | 1 |
Data: Motorwise Workshop. Bulletin 7.
Air conditioning & heating
1 documented fault — symptoms, causes and workshop fixes.
Incorrect display of outside air temperature.
All models, 2017→.
AC/heater blower motor control module software fault.
Workshop instructions
Workshop procedure
- Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
- If no fault(s) found: Re-program AC control module with upgraded software. Note: To carry out an effective repair a software upgrade will be required - refer to manufacturer.
Data: Motorwise Workshop. Bulletin 14.
Wipers & visibility
1 documented fault — symptoms, causes and workshop fixes.
Windscreen wipers intermittent operation or not working.
All models, 2012→.
What you'd notice
Indicators intermittent operation or not working.
The repair
Poor electrical connection between switch assembly and harness multi-plug.
Workshop instructions & parts1 part
Workshop procedure
- Remove windscreen wiper switch.
- Clean windscreen wiper switch harness multi-plug terminals Fig.1217605.1 .
- Lightly coat terminals with grease Fig.1217605.1 . Use specified grease.
- Refit windscreen wiper switch.
- Repeat procedure for indicator switch.
| Part | Part number | Qty |
|---|---|---|
| Electrical contact grease (Nyogel) | LR054614 | 1 |
Data: Motorwise Workshop. Bulletin 2.
Take it with you
Before you view one
Land Rover Discovery Sport 2 eD4 (2015–2019)
Each documented fault as a quick check for a viewing or test drive — tick them off as you go.
A little workshop vocabulary
Workshop terms used on this page
Definitions for the technical language used in these bulletins.
- MIL
- Malfunction indicator lamp — the engine warning light on the dashboard
- ECM
- Engine control module — the car's engine computer
- Nm
- Newton-metres — the standard unit for how tightly a bolt is done up
- EGR
- Exhaust gas recirculation — feeds some exhaust gas back into the intake to cut emissions
- DPF
- Diesel particulate filter — traps soot in the exhaust and burns it off periodically
- Trouble Codes
- Standardised fault codes stored by the engine computer, read with a diagnostic tool
- AC
- Air conditioning — the system that cools the cabin
- ABS/ESP
- Anti-lock braking and electronic stability programme — the computer that stops the wheels locking and keeps the car stable
- LH
- Left-hand — the left side of the vehicle as you sit in it
- NOx
- Nitrogen oxides — exhaust gases the emissions system is designed to cut
- SCR
- Selective catalytic reduction — uses Diesel Exhaust Fluid (AdBlue) to cut NOx emissions
- TCM
- Transmission control module — the gearbox computer
- AC/Heater
- The heating and air-conditioning system
- Anti-Roll Bar
- A bar that links the left and right suspension to cut body roll in corners
- Control Module
- A computer that runs one of the car's systems (engine, gearbox, brakes, body, and so on)
- Crankshaft Pulley
- The pulley on the front of the crankshaft that drives the auxiliary belt
- DPF Regeneration
- The process that burns soot out of the diesel particulate filter, usually on a longer run
- EGR Cooler
- A heat exchanger that cools exhaust gas before it is fed back into the intake
- Fault Memory
- The list of stored trouble codes in a control module
- Instrument Panel
- The dashboard display that shows warning lights and messages
- Multi-Plug
- A multi-pin electrical connector on a wiring harness
- Oil Gallery
- An internal oil passage in the engine
- Re-Program
- Update the software on a control module using the manufacturer's diagnostic tool
- Ride Height
- How high the vehicle sits; on air suspension this can be raised or lowered
- Stop-Start
- The system that cuts the engine at idle and restarts it when you pull away
- Valve Block
- The set of solenoid valves that directs air or fluid in the air-suspension or gearbox
- Wiring Harness
- The bundled cables that carry power and signals around the vehicle
- Auxiliary Drive Belt
- The belt that drives the alternator, water pump, steering pump or air-conditioning compressor
- Blower Motor
- The fan that pushes air through the heater and air-conditioning
- Oil Seal
- A rubber seal that keeps oil in and dirt out, typically around a rotating shaft
- Recirculation
- Air-conditioning mode that recirculates cabin air instead of drawing in outside air
Common questions
Using this guide.
What are the common faults with the Land Rover Discovery Sport 2 eD4?
Garages and workshops regularly encounter 15 documented faults on the Land Rover Discovery Sport 2 eD4 — four concern the engine and fuel system and two the electrical and ignition. Each fault above lists the symptoms, cause, fix and any parts needed.
Does every Land Rover Discovery Sport 2 eD4 have these faults?
No. These are patterns documented across the model by workshops, not predictions for an individual car. Where a fault applies only to certain vehicles or VIN ranges, that is listed with the fault.
Can I check for Land Rover Discovery Sport 2 eD4 faults when viewing one?
Many of them, yes — the documented symptoms are things you can see, hear or feel on a viewing or test drive. The 'Before you view one' checklist above turns each documented fault into a quick check you can tick off as you go.