Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity cc | 2982 |
| Compression ratio :1 | 17,9 |
Injection system
| Air metering Type | Mass/MAP |
|---|---|
| Fuel/injection pump assembly Make | Denso |
| Fuel/injection pump assembly Type | HP3 |
| Pump type | Common rail |
| Engine coolant temperature (ECT) sensor Ohm/°C | 310-326/80 |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor Ohm | 1630-2740 |
| Injector Ohm | 0,42-0,52 |
| Intake air temperature (IAT) sensor Ohm/°C | 2210-2650/20 |
Injection sequence
The injection sequence for the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) is 1-3-4-2.
| Injection sequence | 1-3-4-2 |
|---|
Valve clearances
Valve clearances for the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) are 0,20-0,30 mm inlet and 0,35-0,45 mm exhaust, measured cold.
| Valve clearance - INLET mm | 0,20-0,30 cold |
|---|---|
| Valve clearance - EXHAUST mm | 0,35-0,45 cold |
Engine oil & fluids
Engine oil
The Toyota Landcruiser Prado 3.0 D-4D (2010–2015) takes 7.0 litres of engine oil with the filter.
A listed engine oil option is SAE 0W-30 for all ambient temperatures, with API/ACEA classification /C2.
A listed engine oil option is SAE 5W-30 for all ambient temperatures, with API/ACEA classification /C2.
A listed engine oil option is SAE 5W-30 for all ambient temperatures, with API/ACEA classification CF/B1.
A listed engine oil option is SAE 10W-30 for all ambient temperatures, with API/ACEA classification CF/B1.
A listed engine oil option is SAE 15W-40 for all ambient temperatures, with API/ACEA classification CF.
A listed engine oil option is SAE 20W-50 for all ambient temperatures, with API/ACEA classification CF.
Manual gearbox
The manual gearbox has a listed capacity of 2.1 litres.
See the reference table for the complete manual gearbox entries and their conditions.
Transfer box
See the reference table for the complete transfer box entries and their conditions.
Coolant
See the reference table for the complete coolant entries and their conditions.
Grades, filling conditions and capacities
| Engine oil options | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-30 |
| Engine oil classification API/ACEA | /C2 |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 |
| Engine oil classification API/ACEA | /C2 |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 |
| Engine oil classification API/ACEA | CF/B1 |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 10W-30 |
| Engine oil classification API/ACEA | CF/B1 |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 15W-40 |
| Engine oil classification API/ACEA | CF |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 20W-50 |
| Engine oil classification API/ACEA | CF |
| Engine with filter(s) litres | 7.0 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | 75W LF |
| Manual transmission oil classification | GL-3 |
| Manual transmission litres | 2.1 |
| Fill transmission with specified amount or until transmission oil level is between 0-5 mm from bottom lip of filler hole, otherwise transmission damage may occur. | |
| Automatic transmission fluid Type | Toyota ATF WS |
| Automatic transmission (drain & refill) litres | — |
| View more information | — |
| Checking ATF level | |
| Automatic transmission (dry fill) litres | 10.6 |
| Automatic transmission fluid (ATF) - dry fill | |
| Differential oil grade - front SAE | 75W-85 LT |
| Differential oil classification - front | GL-5 |
| Differential front/AT litres | 1.35-1.45 |
| Fill differential with specified amount or until differential oil level is between 0-5 mm from bottom lip of filler hole, otherwise differential damage may occur. | |
| Differential oil grade - rear SAE | 75W-85 |
| Differential oil classification - rear | GL-5 |
| Differential rear litres | — |
| Transfer box oil grade SAE | 75W LF |
| Transfer box litres | 1.4 |
| Fill transfer box with specified amount or until transfer box oil level is between 0-5 mm from bottom lip of filler hole, otherwise transfer box damage may occur. | |
| Coolant Type | Toyota SLLC |
| Coolant Colour | Pink |
| Cooling system - total capacity litres | 13.2 |
| Cooling system | |
| Brake fluid Type | DOT 3 |
| Clutch fluid Type | DOT 3 |
| Power steering fluid Type | ATF Dexron II/III |
Brakes & wear limits
Brake disc thickness
Brake discs on the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) are replaced at a minimum thickness of 29 mm (ventilated) front and 16 mm (ventilated) rear.
| Minimum disc thickness for replacement - ventilated Front | 29 mm |
|---|---|
| Minimum disc thickness for replacement - ventilated Rear | 16 mm |
| Maximum drum diameter for replacement Rear | 211 mm |
Brake disc and drum dimensions
| Disc runout Front | 0,05 mm |
|---|---|
| Disc runout Rear | 0,20 mm |
| Minimum pad thickness Front | 1 mm |
| Minimum pad thickness Rear | 1 mm |
| Minimum shoe thickness Rear | 1 mm |
| Parking brake travel No. of notches | 5-7 |
Service & electrical
Glow plugs
Glow plugs for the Toyota Landcruiser Prado 3.0 D-4D (2010–2015): Original equipment 19850-30030.
| Glow plug - part no. Original equipment | 19850-30030 |
|---|
Tuning and emissions
| Idle speed rpm | 660±50 DPF=700±50 |
|---|---|
| Idle speed - alternative rpm | AT=700±50 |
| Rated no load speed rpm | 4450-4750 |
| Oil temperature °C | 80 |
| Idle speed - for smoke test rpm | 650-750 |
| Governed speed range - for smoke test rpm | 4450-4750 |
| Maximum time at governed speed secs | 1,8 |
| Test mode A/B | B |
| Probe type 1/2 | 1 |
| Conditioning Accelerations/rpm | 3 |
| Smoke opacity - EU limit m-1 (%) | 3,00 (73) |
| Smoke opacity - homologation value m-1 (%) | 0,49 (19) |
Starting and charging
| Battery V/RC(Ah) | 12 |
|---|---|
| Alternator output A/V/rpm | 30/13,2/2000 |
Service checks and adjustments
| Compression pressure bar | 22,0-27,0 DPF=16,3-20,0 |
|---|---|
| Oil pressure bar/rpm | 0,3 Min/700 |
| Oil pressure | |
| Radiator cap bar | 0,93-1,23 |
| Thermostat opens °C | 80-84 |
Tightening torques
Cylinder head bolt torque
The cylinder head bolts on the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) are tightened in 5 stages: 20 Nm, then 40 Nm, then 85 Nm, then 90°, then a final 90°.
| Cylinder head | |
|---|---|
| Tighten | 20 Nm |
| Tighten | 40 Nm |
| Tighten | 85 Nm |
| Tighten | 90° |
| Tighten | 90° |
| Cylinder head instructions | — |
|---|---|
| Cylinder head | |
| View more information | — |
| Other engine tightening torques | |
| Main bearings Renew bolts/nuts | — |
| View more information | — |
| Main bearings Stage 1 | 50 Nm |
| Main bearings Stage 2 | 90° |
| Big end bearings Renew bolts/nuts | — |
| View more information | — |
| Big end bearings Stage 1 | 35 Nm |
| Big end bearings Stage 2 | 90° |
| Sump bolts | — |
| View more information | — |
| Assemble components within 3 minutes and tighten bolts within 15 minutes. Do NOT start engine for 2 hours. | |
| Sump drain bolt | 34 Nm |
| Flywheel/driveplate | 178 Nm |
| Clutch pressure plate | 19 Nm |
| Crankshaft pulley/damper centre bolt | 365 Nm |
| Camshaft sprocket/gear | 98 Nm |
| Camshaft carrier/cap | 19 Nm |
| Camshaft/rocker cover | — |
| View more information | — |
| Upper cover | |
| Inlet manifold to cylinder head | 29 Nm |
| Exhaust manifold to cylinder head | 40 Nm |
| Exhaust downpipe to manifold | 54 Nm |
| Water pump | — |
| View more information | — |
| Water pump | |
| Injector/clamp | 22 Nm |
| Injector pipe unions | 35 Nm |
| Fuel/injection pump sprocket/gear | 64 Nm |
| Fuel/injection pump flange | 31 Nm |
| Fuel/injection pump mounting | 21 Nm |
| Glow plugs | 18 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 9 Nm |
| Camshaft position (CMP) sensor | 9 Nm |
| Engine coolant temperature (ECT) sensor | 20 Nm |
| Engine oil pressure switch | 15 Nm |
| Oil pressure switch | |
| Oil filter | 17 Nm |
| Chassis tightening torques | |
| Front hub | 235 Nm |
| Front hub - wheel bearing housing bolts | 80 Nm |
| Rear hub - wheel bearing housing bolts | 60 Nm |
| Steering wheel | 50 Nm |
| Steering rack/box mounting | 120 Nm |
| Steering track rod end | 91 Nm |
| Brake disc to hub Front | 112 Nm |
| Brake caliper/carrier to hub Front | 123 Nm |
| Brake disc to hub Rear | 112 Nm |
| Brake caliper to carrier Rear | 88 Nm |
| Brake caliper/carrier to hub Rear | 100 Nm |
| Back plate to hub Rear | 60 Nm |
| ABS sensor Front | 9 Nm |
| ABS sensor Rear | 8 Nm |
| Road wheels | — |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | No |
| Air conditioning refrigerant Type | — |
| Do not mix R134a with R1234yf. | |
| Air conditioning refrigerant quantity grams | — |
| Air conditioning oil group | PAG |
| Air conditioning oil Type | — |
| Do not mix different oil types. | |
| Air conditioning oil quantity cm³ | — |
Frequently asked questions
What is the injection sequence of the Toyota Landcruiser Prado 3.0 D-4D?
The injection sequence for the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) is 1-3-4-2.
What glow plugs does the Toyota Landcruiser Prado 3.0 D-4D use?
Glow plugs for the Toyota Landcruiser Prado 3.0 D-4D (2010–2015): Original equipment 19850-30030.
How much oil does the Toyota Landcruiser Prado 3.0 D-4D take?
The Toyota Landcruiser Prado 3.0 D-4D (2010–2015) takes 7.0 litres of engine oil with the filter. A listed engine oil option is SAE 0W-30 for all ambient temperatures, with API/ACEA classification /C2. A listed engine oil option is SAE 5W-30 for all ambient temperatures, with API/ACEA classification /C2. A listed engine oil option is SAE 5W-30 for all ambient temperatures, with API/ACEA classification CF/B1. A listed engine oil option is SAE 10W-30 for all ambient temperatures, with API/ACEA classification CF/B1. A listed engine oil option is SAE 15W-40 for all ambient temperatures, with API/ACEA classification CF. A listed engine oil option is SAE 20W-50 for all ambient temperatures, with API/ACEA classification CF.
What are the valve clearances for the Toyota Landcruiser Prado 3.0 D-4D?
Valve clearances for the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) are 0,20-0,30 mm inlet and 0,35-0,45 mm exhaust, measured cold.
What is the cylinder head torque for the Toyota Landcruiser Prado 3.0 D-4D?
The cylinder head bolts on the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) are tightened in 5 stages: 20 Nm, then 40 Nm, then 85 Nm, then 90°, then a final 90°.
What is the minimum brake disc thickness for the Toyota Landcruiser Prado 3.0 D-4D?
Brake discs on the Toyota Landcruiser Prado 3.0 D-4D (2010–2015) are replaced at a minimum thickness of 29 mm (ventilated) front and 16 mm (ventilated) rear.