Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity cc | 2982 |
| Compression ratio :1 | 16,0 |
Injection system
| Air metering Type | Mass/MAP |
|---|---|
| Pump type | Common rail |
| Engine coolant temperature (ECT) sensor Ohm/°C | 310-326/80 |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor Ohm | 1630-2740 |
| Intake air temperature (IAT) sensor Ohm/°C | 2210-2650/20 |
Injection sequence
The injection sequence for the Toyota Dyna 3.0 D-4D (2007–2012) is 1-3-4-2.
| Injection sequence | 1-3-4-2 |
|---|
Valve clearances
Valve clearances for the Toyota Dyna 3.0 D-4D (2007–2012) are 0,20-0,30 mm inlet and 0,35-0,45 mm exhaust, measured cold.
| Valve clearance - INLET mm | 0,20-0,30 cold |
|---|---|
| Valve clearance - EXHAUST mm | 0,35-0,45 cold |
Engine oil & fluids
Engine oil
The Toyota Dyna 3.0 D-4D (2007–2012) takes 7.0 litres of engine oil with the filter.
See the reference table for the complete engine oil entries and their conditions.
Manual gearbox
The manual gearbox has a listed capacity of 2.2-2.6 litres. The specified oil is SAE 75W-90, with classification GL-4/5.
Coolant
The listed total cooling-system capacity is 9.8 litres.
See the reference table for the complete coolant entries and their conditions.
Grades, filling conditions and capacities
| Preferred engine oil | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 Synthetic |
| Engine oil classification API/ACEA | CF/B1 DPF=C2 |
| Engine oil options | |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-30 Synthetic |
| Engine oil classification API/ACEA | /C2 |
| Ambient temperature range | -18°C➞38°C |
| Engine oil grade SAE | 10W-30 Synthetic |
| Engine oil classification API/ACEA | CF/B1 |
| Ambient temperature range | -12°C➞38°C |
| Engine oil grade SAE | 15W-40 |
| Engine oil classification API/ACEA | CF/B1 |
| Ambient temperature range | -7°C➞38°C |
| Engine oil grade SAE | 20W-50 |
| Engine oil classification API/ACEA | CF/B1 |
| Engine with filter(s) litres | 7.0 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | 75W-90 |
| Manual transmission oil classification | GL-4/5 |
| Manual transmission litres | 2.2-2.6 |
| Differential oil grade - rear SAE | — |
| Differential oil classification - rear | GL-5 |
| Differential rear litres | 1.7-3.4 |
| Coolant Type | Super long life |
| Coolant Colour | Pink |
| Cooling system - total capacity litres | 9.8 |
| Brake fluid Type | DOT 3 |
| Power steering fluid Type | Dexron II/III |
Brakes & wear limits
Brake disc thickness
Front brake discs on the Toyota Dyna 3.0 D-4D (2007–2012) are replaced at a minimum thickness of 26 mm (ventilated).
| Minimum disc thickness for replacement - ventilated Front | 26 mm |
|---|---|
| Maximum drum diameter for replacement Rear | — |
Brake disc and drum dimensions
| Disc runout Front | 0,12 mm |
|---|---|
| Minimum pad thickness Front | 3 mm |
| Minimum shoe thickness Rear | 1 mm |
| Parking brake travel No. of notches | 4-6 |
Service & electrical
Tuning and emissions
| Idle speed rpm | 750±50 |
|---|---|
| Rated no load speed rpm | 4450-4750 |
| Oil temperature °C | 80 |
| Idle speed - for smoke test rpm | 600-800 |
| Governed speed range - for smoke test rpm | 4450-4750 |
| Maximum time at governed speed secs | 1,8 |
| Test mode A/B | B |
| Probe type 1/2 | 1 |
| Conditioning Accelerations/rpm | 3 |
| Smoke opacity - EU limit m-1 (%) | 3,00 (73) |
| Smoke opacity - homologation value m-1 (%) | 1,50 (48) |
Service checks and adjustments
| Compression pressure bar | 16,3-20,0 |
|---|---|
| Oil pressure bar/rpm | — |
| Radiator cap bar | 0,93-1,23 |
| Thermostat opens °C | 80-84 |
Tightening torques
Cylinder head bolt torque
The cylinder head bolts on the Toyota Dyna 3.0 D-4D (2007–2012) are tightened in 5 stages: 20 Nm, then 40 Nm, then 85 Nm, then 90°, then a final 90°.
| Cylinder head | |
|---|---|
| Tighten | 20 Nm |
| Tighten | 40 Nm |
| Tighten | 85 Nm |
| Tighten | 90° |
| Tighten | 90° |
| Cylinder head instructions | — |
|---|---|
| Cylinder head | |
| View more information | — |
| Other engine tightening torques | |
| Main bearings Renew bolts/nuts | — |
| View more information | — |
| Main bearings Stage 1 | 50 Nm |
| Main bearings Stage 2 | 90° |
| Big end bearings Renew bolts/nuts | — |
| View more information | — |
| Big end bearings Stage 1 | 35 Nm |
| Big end bearings Stage 2 | 90° |
| Sump bolts | 12 Nm |
| Sump drain bolt | 34 Nm |
| Flywheel/driveplate | 178 Nm |
| Clutch pressure plate | 19 Nm |
| Crankshaft pulley/damper centre bolt | 365 Nm |
| Camshaft sprocket/gear | 98 Nm |
| Camshaft carrier/cap | 19 Nm |
| Camshaft/rocker cover | 9 Nm |
| Inlet manifold to cylinder head | 29 Nm |
| Exhaust manifold to cylinder head | 40 Nm |
| Exhaust downpipe to manifold | 43 Nm |
| Water pump | 13 Nm |
| Injector/clamp | 22 Nm |
| Injector pipe unions | 35 Nm |
| Fuel/injection pump sprocket/gear | 64 Nm |
| Fuel/injection pump flange | 21 Nm |
| Glow plugs | 13 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 9 Nm |
| Camshaft position (CMP) sensor | 9 Nm |
| Engine coolant temperature (ECT) sensor | 20 Nm |
| Nitrogen oxide (NOx) sensor | 30 Nm |
| Engine oil pressure switch | 15 Nm |
| Oil filter | 17 Nm |
| Chassis tightening torques | |
| Front hub | — |
| Rear hub | — |
| If turning force is as specified, align lock plate mark with axle housing mark. | |
| Rear hub - wheel bearing housing bolts | — |
| With leading and trailing brake shoes | |
| Steering wheel | 50 Nm |
| Steering rack/box mounting | 120 Nm |
| Steering track rod end | 91 Nm |
| Brake disc to hub Front | 61 Nm |
| Brake caliper to carrier Front | 39 Nm |
| Brake caliper/carrier to hub Front | 147 Nm |
| ABS sensor Front | 8 Nm |
| ABS sensor Rear | 8 Nm |
| Road wheels | — |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | No |
| Air conditioning refrigerant Type | R134a |
| Air conditioning refrigerant quantity grams | 500±50 |
| Air conditioning oil group | PAG |
| Air conditioning oil Type | Dens Oil 8 |
| Air conditioning oil quantity cm³ | — |
| Air conditioning oil viscosity ISO | 46 |
Frequently asked questions
What is the injection sequence of the Toyota Dyna 3.0 D-4D?
The injection sequence for the Toyota Dyna 3.0 D-4D (2007–2012) is 1-3-4-2.
How much oil does the Toyota Dyna 3.0 D-4D take?
The Toyota Dyna 3.0 D-4D (2007–2012) takes 7.0 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.
What are the valve clearances for the Toyota Dyna 3.0 D-4D?
Valve clearances for the Toyota Dyna 3.0 D-4D (2007–2012) are 0,20-0,30 mm inlet and 0,35-0,45 mm exhaust, measured cold.
What is the cylinder head torque for the Toyota Dyna 3.0 D-4D?
The cylinder head bolts on the Toyota Dyna 3.0 D-4D (2007–2012) are tightened in 5 stages: 20 Nm, then 40 Nm, then 85 Nm, then 90°, then a final 90°.
What is the minimum brake disc thickness for the Toyota Dyna 3.0 D-4D?
Front brake discs on the Toyota Dyna 3.0 D-4D (2007–2012) are replaced at a minimum thickness of 26 mm (ventilated).