Engine & identification
Vehicle identification
| No. of cylinders Type | 4/OHC |
|---|---|
| Capacity cc | 1364 |
Injection system
| Air metering Type | Mass/MAP |
|---|---|
| Pump type | Common rail |
| Engine coolant temperature (ECT) sensor Ohm/°C | 2320-2590/20 |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor Ohm | 1630-2740 |
| Intake air temperature (IAT) sensor Ohm/°C | 2210-2650/20 |
Injection sequence
The injection sequence for the Toyota Corolla 1.4 D-4D (2013–2018) is 1-3-4-2.
| Injection sequence | 1-3-4-2 |
|---|
Valve clearances
Valve clearances for the Toyota Corolla 1.4 D-4D (2013–2018) are 0,11-0,17 mm inlet and 0,14-0,20 mm exhaust, measured cold.
| Valve clearance - INLET mm | 0,11-0,17 cold |
|---|---|
| Valve clearance - EXHAUST mm | 0,14-0,20 cold |
Engine oil & fluids
Engine oil
The Toyota Corolla 1.4 D-4D (2013–2018) takes 3.9 litres of engine oil with the filter.
The preferred engine oil is SAE 0W-30 for all ambient temperatures, with API/ACEA classification /C2.
A listed engine oil option is SAE 5W-30 for all ambient temperatures, with API/ACEA classification /C2.
Manual gearbox
See the reference table for the complete manual gearbox entries and their conditions.
Coolant
The listed total cooling-system capacity is 5.6 litres.
See the reference table for the complete coolant entries and their conditions.
Grades, filling conditions and capacities
| Preferred engine oil | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-30 |
| Engine oil classification API/ACEA | /C2 |
| Engine oil options | |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 |
| Engine oil classification API/ACEA | /C2 |
| Engine with filter(s) litres | 3.9 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | 75W |
| Manual transmission oil classification | GL-4 |
| Manual transmission litres | 2.4 |
| Auto shift manual (ASM) transmission oil grade SAE | 75W |
| Auto shift manual (ASM) transmission oil classification | GL-4 |
| Auto shift manual (ASM) transmission (drain & refill) litres | 2.4 |
| Coolant Type | Toyota SLLC |
| Coolant Colour | Pink |
| Cooling system - total capacity litres | 5.6 |
| Brake fluid Type | — |
| View more information | — |
Brakes & wear limits
Brake disc thickness
Rear brake discs on the Toyota Corolla 1.4 D-4D (2013–2018) are replaced at a minimum thickness of 8 mm.
| Minimum disc thickness for replacement - ventilated Front | — |
|---|---|
| Minimum disc thickness for replacement Rear | 8 mm |
Brake disc and drum dimensions
| Disc runout Front | 0,05 mm |
|---|---|
| Disc runout Rear | 0,15 mm |
| Minimum pad thickness Front | 1 mm |
| Minimum pad thickness Rear | 1 mm |
| Parking brake travel No. of notches | 5-8 |
Service & electrical
Tuning and emissions
| Idle speed rpm | 770±50 |
|---|---|
| Rated no load speed rpm | 5150-5250 |
| Oil temperature °C | 80 |
| Idle speed - for smoke test rpm | 720-820 |
| Governed speed range - for smoke test rpm | 5100-5250 |
| Maximum time at governed speed secs | 1,0 |
| Test mode A/B | B |
| Probe type 1/2 | 1 |
| Conditioning Accelerations/rpm | 3/5100-5250 |
| Smoke opacity - EU limit m-1 (%) | 1,50 (48) |
| Smoke opacity - homologation value m-1 (%) | 0,5 (19) |
Starting and charging
| Alternator output A/V/rpm | 30/12/2000 |
|---|
Service checks and adjustments
| Compression pressure bar | 20,5-23,0 |
|---|---|
| Oil pressure bar/rpm | 0,2 Min/770 |
| Radiator cap bar | 0,78-1,23 |
| Thermostat opens °C | 80-84 |
Glow plugs
| Glow plug activation time secs | 3,0 |
|---|
Tightening torques
Cylinder head bolt torque
The cylinder head bolts on the Toyota Corolla 1.4 D-4D (2013–2018) are tightened in 5 stages: 25 Nm, then 50 Nm, then 90°, then 90°, then a final 90°.
| Cylinder head | |
|---|---|
| Tighten | 25 Nm |
| Tighten | 50 Nm |
| Tighten | 90° |
| Tighten | 90° |
| Tighten | 90° |
| Cylinder head instructions | — |
|---|---|
| View more information | — |
| Other engine tightening torques | |
| Main bearings Renew bolts/nuts | — |
| Main bearings Stage 1 | 60 Nm |
| Main bearings Stage 2 | 90° |
| Big end bearings Renew bolts/nuts | — |
| View more information | — |
| Big end bearings Stage 1 | 15 Nm |
| Big end bearings Stage 2 | 90° |
| Oil pump to cylinder block | 9 Nm |
| Sump bolts | — |
| View more information | — |
| Assemble components within 3 minutes and tighten bolts within 10 minutes. Do NOT start engine for 2 hours. | |
| Sump drain bolt | 38 Nm |
| Flywheel/driveplate | 49 Nm+90° |
| Clutch pressure plate | 19 Nm |
| Crankshaft pulley/damper centre bolt | 210 Nm |
| Camshaft sprocket/gear | 20 Nm |
| Camshaft carrier/cap | 19 Nm |
| Camshaft/rocker cover | 11 Nm |
| View more information | — |
| Exhaust manifold to cylinder head | 43 Nm |
| Exhaust downpipe to manifold | 43 Nm |
| Water pump | 21 Nm |
| Injector/clamp | 19 Nm |
| Injector pipe unions | 28 Nm |
| Fuel/injection pump flange | 21 Nm |
| Glow plugs | 13 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 7 Nm |
| Camshaft position (CMP) sensor | 7 Nm |
| Engine coolant temperature (ECT) sensor | 20 Nm |
| Engine oil pressure switch | 15 Nm |
| Oil filter | 25 Nm |
| Chassis tightening torques | |
| Front hub | 216 Nm |
| Front hub - wheel bearing housing bolts | 96 Nm |
| Rear hub - wheel bearing housing bolts | 90 Nm |
| Steering wheel | 50 Nm |
| Steering rack/box mounting | 110 Nm |
| Steering track rod end | 49 Nm |
| Do not lubricate. | |
| Brake caliper to carrier Front | — |
| Brake caliper/carrier to hub Front | 107 Nm |
| ABS sensor Front | 9 Nm |
| Road wheels | 103 Nm |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | No |
| Compressor variable displacement solenoid | Yes |
| Air conditioning refrigerant Type | — |
| Do not mix R134a with R1234yf. | |
| Air conditioning refrigerant quantity grams | — |
| Air conditioning oil group | PAG |
| Air conditioning oil Type | — |
| Air conditioning oil viscosity ISO | 46 |
Frequently asked questions
What is the injection sequence of the Toyota Corolla 1.4 D-4D?
The injection sequence for the Toyota Corolla 1.4 D-4D (2013–2018) is 1-3-4-2.
How much oil does the Toyota Corolla 1.4 D-4D take?
The Toyota Corolla 1.4 D-4D (2013–2018) takes 3.9 litres of engine oil with the filter. The preferred engine oil is SAE 0W-30 for all ambient temperatures, with API/ACEA classification /C2. A listed engine oil option is SAE 5W-30 for all ambient temperatures, with API/ACEA classification /C2.
What are the valve clearances for the Toyota Corolla 1.4 D-4D?
Valve clearances for the Toyota Corolla 1.4 D-4D (2013–2018) are 0,11-0,17 mm inlet and 0,14-0,20 mm exhaust, measured cold.
What is the cylinder head torque for the Toyota Corolla 1.4 D-4D?
The cylinder head bolts on the Toyota Corolla 1.4 D-4D (2013–2018) are tightened in 5 stages: 25 Nm, then 50 Nm, then 90°, then 90°, then a final 90°.
What is the minimum brake disc thickness for the Toyota Corolla 1.4 D-4D?
Rear brake discs on the Toyota Corolla 1.4 D-4D (2013–2018) are replaced at a minimum thickness of 8 mm.