Toyota1990–1992Technical specifications

Corolla 1.3: Technical specifications

Workshop data for the 1.3-litre petrol (engine code 2E). Covers engine, fluids, brakes, service, torques and air conditioning: the figures to check before a job or a parts order.

Summary

Match the engine code (2E) to the vehicle before ordering parts or applying these figures.

Vehicle specifications

Overview

Make
Toyota
Model
Corolla
Years
1990–1992
Fuel
Petrol
Engine code
2E

Performance & efficiency

Power
60 kW (82 hp)
Engine size
1,295 cc
Cylinders
4 · OHC
Compression ratio
9.5:1
Fuel system
Aisan

Fluids & capacities

Engine oil (with the filter)
3.2 litres
All 137 specifications below

Engine & identification

Vehicle identification

No. of cylinders Type4/OHC
Capacity (Fiscal) cc1295 (1280)
Compression ratio :19,5
Suitable for unleaded petrolYes
Minimum octane rating RON95
Ignition system TypeIIA
Ignition system DescriptionTrans-i
Trigger locationDistributor
Fuel system MakeAisan
Fuel system Type11680
Fuel system DescriptionCarb-FJ
Diagnostic socketNo

Ignition system

Ignition coil MakeDenso
Ignition coil supply voltage + with ballast V11,0
Primary resistance Ohm1,26-1,54
Secondary resistance Ohm10200-13800
Distributor (ECM) MakeDenso
Distributor (ECM) No.11142
Contact breaker gap/trigger air gap mm0,2-0,4

Firing order

The firing order for the Toyota Corolla 1.3 (1990–1992) is 1-3-4-2.

Firing order1-3-4-2

Valve clearances

Valve clearances for the Toyota Corolla 1.3 (1990–1992) are 0,20 mm inlet and 0,20 mm exhaust, measured hot.

Valve clearance - INLET mm0,20 hot
Valve clearance - EXHAUST mm0,20 hot

Engine oil & fluids

Engine oil

The Toyota Corolla 1.3 (1990–1992) takes 3.2 litres of engine oil with the filter.

A listed engine oil option is SAE 5W-30 for cold climates, with API/ACEA classification SH/A1.

A listed engine oil option is SAE 10W-30 for moderate climates, with API/ACEA classification SH/A1.

A listed engine oil option is SAE 10W-40 as an alternative for moderate climates, with API/ACEA classification SH/A2.

A listed engine oil option is SAE 20W-40 for hot climates, with API/ACEA classification SH/A1.

Manual gearbox

The manual gearbox has a listed capacity of 2.4 litres. The specified oil is Dexron II.

Coolant

The total cooling-system capacity entries are 4.9 litres without a stated condition; 4.8 litres for AT.

Grades, filling conditions and capacities

Lubricants and capacities — complete reference
Engine oil options
Ambient temperature range Cold climate
Engine oil grade SAE 5W-30
Engine oil classification API/ACEA SH/A1
Ambient temperature range Moderate climate
Engine oil grade SAE 10W-30
Engine oil classification API/ACEA SH/A1
Ambient temperature range Moderate climate alternative
Engine oil grade SAE 10W-40
Engine oil classification API/ACEA SH/A2
Ambient temperature range Hot climate
Engine oil grade SAE 20W-40
Engine oil classification API/ACEA SH/A1
Engine with filter(s) litres 3.2
Other lubricants and capacities
Manual transmission oil grade SAE Dexron II
Manual transmission litres 2.4
Automatic transmission fluid Type Dexron II
Automatic transmission (drain & refill) litres 2.5
Automatic transmission (dry fill) litres 5.5
Differential front/AT litres AT=1,4
Differential oil grade - rear SAE Dexron II
Cooling system - total capacity litres 4,9 AT=4,8
Brake fluid Type DOT 3
Power steering fluid Type Dexron II
Power steering fluid litres 0.8

Brakes & wear limits

Brake disc thickness

Brake discs on the Toyota Corolla 1.3 (1990–1992) are replaced at a minimum thickness of 11 mm (solid) or 16 mm (ventilated) front; the rear brake drums are replaced at a maximum diameter of 201 mm.

Minimum disc thickness for replacement - solid Front11 mm
Minimum disc thickness for replacement - ventilated Front16 mm
Maximum drum diameter for replacement Rear201 mm

Brake disc and drum dimensions

Disc runout Front0,15 mm
Minimum pad thickness Front1 mm
Minimum shoe thickness Rear1 mm
Parking brake travel No. of notches4-7

Service & electrical

Ignition timing

Basic ignition timing for the Toyota Corolla 1.3 (1990–1992) is 5° BTDC at 800 rpm.

Ignition timingWithout vacuum
Ignition timing - basic BTDC °Engine/rpm5/800

Battery

The Toyota Corolla 1.3 (1990–1992) uses a 12 V, 60 Ah battery (reserve capacity 90 minutes).

Battery V/RC(Ah)12/90 (60)

Spark plugs

The Toyota Corolla 1.3 (1990–1992) uses NGK BPR5EY-11 spark plugs with a 1,1 mm electrode gap.

Spark plugs Original equipmentNGK
Spark plug TypeBPR5EY-11
Electrode gap mm1,1
Spark plugs MakeBosch
Spark plug TypeWR8DCX
Electrode gap mm1,1
Spark plugs MakeChampion
Spark plug TypeRN9YCC4
Electrode gap mm1,0
Spark plugs MakeNGK
Spark plug TypeBPR5EY-11
Electrode gap mm1,1

Tuning and emissions

Ignition advanceWithout vacuum and basic timing
Ignition advance checks °Engine/rpm1-4/1550
Ignition advance checks °Engine/rpm16-19/3600
Ignition advance checks °Engine/rpm19-23/5600
Vacuum checkIgnition timing advances
Vacuum range °Engine23-27
Vacuum starts mbar133
Vacuum ends mbar587
Idle speed rpm800
Idle speed - alternative rpmAT=850
Fast idle speed - MT/AT rpm1600
Oil temperature °C60-80
CO level at idle speed - tailpipe Vol. % CO1,0-2,0
HC level at idle speed ppm300
CO2 level at idle speed Vol. % CO213-16
O2 level at idle speed Vol. % O20,5-2,0

Starting and charging

Starter motor MakeDenso
Starter motor Type12V 1,0 kW
Minimum starting voltage V8
Maximum cranking amps A162-198
Alternator MakeNippon Denso
Alternator Type12V 50A
Alternator output A/V/rpm30/14/2000
Voltage regulator TypeIC
Regulated voltage V13,5-15,1

Service checks and adjustments

Compression pressure bar9,8-12,7
Oil pressure bar/rpm2,5-5,0/3000
Radiator cap bar0,75-1,05
Thermostat opens °C80-84
Drive belt size - alternator mm4PKx810
Drive belt size - PAS/AC mm5PKx863
Drive belt tension - alternator/PAS/AC mm5-6/11-13

Fuel system

Fuel pump delivery pressure bar0,2-0,3

Tightening torques

Cylinder head bolt torque

The cylinder head bolts on the Toyota Corolla 1.3 (1990–1992) are tightened in 3 stages: 29 Nm, then 49 Nm, then a final 90°.

Cylinder head
Renew boltsNo
Tighten29 Nm
Tighten49 Nm
Tighten90°
Cylinder head instructions—
Other engine tightening torques
Main bearings Renew bolts/nutsNo
Main bearings Stage 128 Nm
Main bearings Stage 257 Nm
Big end bearings Renew bolts/nutsNo
Big end bearings Stage 120 Nm
Big end bearings Stage 239 Nm
Oil pump to cylinder block7 Nm
Sump bolts8 Nm
Sump drain bolt25 Nm
Flywheel/driveplate83 Nm/64 Nm
Clutch pressure plate19 Nm
Crankshaft pulley/damper centre bolt152 Nm
Camshaft sprocket/gear50 Nm
Camshaft carrier/cap14 Nm
Camshaft/rocker cover7 Nm
Inlet manifold to cylinder head19 Nm
Exhaust manifold to cylinder head47 Nm
Spark plugs18 Nm
Chassis tightening torques
Front hub186 Nm
Rear hub123 Nm
Steering track rod end49 Nm
Brake caliper to carrier Front20 Nm
Brake caliper/carrier to hub Front88 Nm
Brake caliper to carrier Rear20 Nm
Brake caliper/carrier to hub Rear47 Nm
Back plate to hub Rear80 Nm
ABS sensor Front8 Nm
ABS sensor Rear8 Nm
Road wheels103 Nm

Air conditioning

Air conditioning refrigerant TypeR12
Air conditioning refrigerant quantity grams675±75
Air conditioning oil TypeDens Oil 6

Frequently asked questions

What is the firing order of the Toyota Corolla 1.3?

The firing order for the Toyota Corolla 1.3 (1990–1992) is 1-3-4-2.

What spark plugs does the Toyota Corolla 1.3 use?

The Toyota Corolla 1.3 (1990–1992) uses NGK BPR5EY-11 spark plugs with a 1,1 mm electrode gap.

How much oil does the Toyota Corolla 1.3 take?

The Toyota Corolla 1.3 (1990–1992) takes 3.2 litres of engine oil with the filter. A listed engine oil option is SAE 5W-30 for cold climates, with API/ACEA classification SH/A1. A listed engine oil option is SAE 10W-30 for moderate climates, with API/ACEA classification SH/A1. A listed engine oil option is SAE 10W-40 as an alternative for moderate climates, with API/ACEA classification SH/A2. A listed engine oil option is SAE 20W-40 for hot climates, with API/ACEA classification SH/A1.

What are the valve clearances for the Toyota Corolla 1.3?

Valve clearances for the Toyota Corolla 1.3 (1990–1992) are 0,20 mm inlet and 0,20 mm exhaust, measured hot.

What is the cylinder head torque for the Toyota Corolla 1.3?

The cylinder head bolts on the Toyota Corolla 1.3 (1990–1992) are tightened in 3 stages: 29 Nm, then 49 Nm, then a final 90°.

What is the ignition timing for the Toyota Corolla 1.3?

Basic ignition timing for the Toyota Corolla 1.3 (1990–1992) is 5° BTDC at 800 rpm.

More on the Corolla