Toyota1995–1997Technical specifications

Corolla 1.3 16V: Technical specifications

Workshop data for the 1.3-litre petrol (engine code 4E-FE). Covers engine, fluids, brakes, service, torques and air conditioning: the figures to check before a job or a parts order.

Summary

Match the engine code (4E-FE) to the vehicle before ordering parts or applying these figures.

Vehicle specifications

Overview

Make: Toyota
Model: Corolla
Years: 1995–1997
Fuel: Petrol
Engine code: 4E-FE

Performance & efficiency

Power: 55 kW (75 hp)
Engine size: 1,332 cc
Cylinders: 4 · DOHC
Compression ratio: 9.6:1
Fuel system: Toyota

Fluids & capacities

Engine oil (with the filter): 2.8-3.2 litres

All 126 specifications below

Engine & identification

Vehicle identification

No. of cylinders Type	4/DOHC
Capacity (Fiscal) cc	1332
Compression ratio :1	9,6
Suitable for unleaded petrol	Yes
Minimum octane rating RON	95
Ignition system Make	Denso
Ignition system Type	ESA
Ignition system Description	Map-i
Trigger location	Distributor
Fuel system Make	Toyota
Fuel system Type	TCCS
Fuel system Description	MFI-i
Air metering Type	MAP
Combined ignition and fuel ECM	Yes
Diagnostic socket	Yes

Ignition system

Ignition coil Make	Denso
Ignition coil supply voltage + with ballast V	11,0
Primary resistance Ohm	1,11-1,75
Secondary resistance Ohm	9000-15700
Distributor (ECM) Make	Toyota
Distributor (ECM) No.	IIA
Contact breaker gap/trigger air gap mm	0,2-0,4

Firing order

The firing order for the Toyota Corolla 1.3 16V (1995–1997) is 1-3-4-2.

Firing order	1-3-4-2

Valve clearances

Valve clearances for the Toyota Corolla 1.3 16V (1995–1997) are 0,15-0,25 mm inlet and 0,31-0,41 mm exhaust, measured cold.

Valve clearance - INLET mm	0,15-0,25 cold
Valve clearance - EXHAUST mm	0,31-0,41 cold

Engine oil & fluids

Engine oil

The Toyota Corolla 1.3 16V (1995–1997) takes 2.8-3.2 litres of engine oil with the filter.

See the reference table for the complete engine oil entries and their conditions.

Manual gearbox

The manual gearbox has a listed capacity of 2.4 litres. The specified oil is SAE 75W-90.

Coolant

The total cooling-system capacity entries are 4.6 litres without a stated condition; 4.7 litres for AT.

Grades, filling conditions and capacities

Lubricants and capacities — complete reference
Engine oil options
Ambient temperature range	-29°C➞10°C
Engine oil grade SAE	5W-30
Engine oil classification API/ACEA	SJ/A1, A3
Ambient temperature range	-18°C➞38°C
Engine oil grade SAE	10W-30
Engine oil classification API/ACEA	SJ/A1, A3
Ambient temperature range	-12°C➞38°C
Engine oil grade SAE	15W-40
Engine oil classification API/ACEA	SJ/A2
Ambient temperature range	-7°C➞38°C
Engine oil grade SAE	20W-50
Engine oil classification API/ACEA	SJ/A2
Engine with filter(s) litres	2.8-3.2
Other lubricants and capacities
Manual transmission oil grade SAE	75W-90
Manual transmission litres	2.4
Automatic transmission fluid Type	Dexron II
Automatic transmission (drain & refill) litres	1.4
Automatic transmission (dry fill) litres	5.5
Cooling system - total capacity litres	4,6 AT=4,7
Brake fluid Type	DOT 3
Power steering fluid Type	Dexron II
Power steering fluid litres	0.8

Brakes & wear limits

Brake disc thickness

The rear brake drums on the Toyota Corolla 1.3 16V (1995–1997) are replaced at a maximum diameter of 201 mm.

Minimum disc thickness
Minimum disc thickness for replacement - ventilated Front	—
Maximum drum diameter for replacement Rear	201 mm

Brake disc and drum dimensions

Minimum disc thickness
Disc runout Front	0,09 mm
Minimum pad thickness Front	1 mm
Minimum shoe thickness Rear	1 mm
Parking brake travel No. of notches	5-8

Service & electrical

Ignition timing

Basic ignition timing for the Toyota Corolla 1.3 16V (1995–1997) is 10° BTDC at 700 rpm.

Idle speed
Ignition timing - basic BTDC °Engine/rpm	10/700

Battery

The Toyota Corolla 1.3 16V (1995–1997) uses a 12 V, 50 Ah battery (reserve capacity 80 minutes).

Battery V/RC(Ah)	12/80 (50)

Spark plugs

The Toyota Corolla 1.3 16V (1995–1997) uses NGK BKR6EYA spark plugs with a 0,8 mm electrode gap.

Spark plugs Original equipment	NGK
Spark plug Type	BKR6EYA
Electrode gap mm	0,8
Spark plugs Make	Champion
Spark plug Type	RC10YC
Electrode gap mm	0,8
Spark plugs Make	NGK
Spark plug Type	BKR6EYA
Electrode gap mm	0,8

Tuning and emissions

Idle speed
Tuning conditions	—
View more information	—
Ignition advance checks °Engine/rpm	ECM Controlled
Idle speed rpm	700±50
Oil temperature °C	80
CO level at idle speed - tailpipe Vol. % CO	0,5 Max Not adjustable
HC level at idle speed ppm	100
CO2 level at idle speed Vol. % CO2	14,5-16
O2 level at idle speed Vol. % O2	0,1-0,5
Increased idle speed for CO test rpm	2400-2600
CO content at increased idle speed Vol. %	0,3
Lambda at increased idle λ	0,98-1,02

Starting and charging

Maximum cranking amps A	135-165
Alternator output A/V/rpm	30/13,5/2000

Service checks and adjustments

Compression pressure bar	9,8-12,8
Oil pressure bar/rpm	2,45-4,9/3000
Radiator cap bar	0,74-1,03
Thermostat opens °C	80-84
Drive belt tension - alternator/PAS/AC mm	5-6,5/9-10,5

Fuel system

System pressure bar	2,87-2,93
Regulated pressure with vacuum bar	2,3-2,6
Engine coolant temperature (ECT) sensor Ohm/°C	250-400/80
Crankshaft position (CKP) sensor/engine speed (RPM) sensor Ohm	400-600
Injector Ohm	13,8
Lambda sensor (Oxygen) heater Ohm	5,0-6,3

Tightening torques

Cylinder head bolt torque

The cylinder head bolts on the Toyota Corolla 1.3 16V (1995–1997) are tightened in 3 stages: 22 Nm, then 44 Nm, then a final 90°.

Cylinder head
Renew bolts	No
Tighten	22 Nm
Tighten	44 Nm
Tighten	90°

Other engine tightening torques
Cylinder head instructions	—
Main bearings Renew bolts/nuts	No
Main bearings Stage 1	28 Nm
Main bearings Stage 2	57 Nm
Big end bearings Renew bolts/nuts	No
Big end bearings Stage 1	20 Nm
Big end bearings Stage 2	39 Nm
Oil pump to cylinder block	8 Nm
Sump bolts	8 Nm
Sump drain bolt	25 Nm
Flywheel/driveplate	88 Nm/88 Nm
Clutch pressure plate	19 Nm
Crankshaft pulley/damper centre bolt	152 Nm
Camshaft sprocket/gear	50 Nm
Camshaft carrier/cap	13 Nm
Camshaft/rocker cover	7 Nm
Inlet manifold to cylinder head	19 Nm
Exhaust manifold to cylinder head	47 Nm
Spark plugs	18 Nm
Chassis tightening torques
Front hub	216 Nm
Rear hub	123 Nm
Steering track rod end	49 Nm
Brake disc to hub Front	80 Nm
Brake caliper to carrier Front	34 Nm
Brake caliper/carrier to hub Front	88 Nm
ABS sensor Front	8 Nm
ABS sensor Rear	8 Nm
Road wheels	103 Nm

Air conditioning

Oil type
No. of AC service connectors	2
Air conditioning restrictor type	Expansion valve
Compressor clutch/magnetic coupling	Yes
Compressor variable displacement solenoid	No
Air conditioning refrigerant Type	R134a
Air conditioning refrigerant quantity grams	700±50
Air conditioning oil group	PAG
Air conditioning oil Type	Dens Oil 9
Air conditioning oil quantity cm³	—
Air conditioning oil viscosity ISO	100

Frequently asked questions

What is the firing order of the Toyota Corolla 1.3 16V?

The firing order for the Toyota Corolla 1.3 16V (1995–1997) is 1-3-4-2.

What spark plugs does the Toyota Corolla 1.3 16V use?

The Toyota Corolla 1.3 16V (1995–1997) uses NGK BKR6EYA spark plugs with a 0,8 mm electrode gap.

How much oil does the Toyota Corolla 1.3 16V take?

The Toyota Corolla 1.3 16V (1995–1997) takes 2.8-3.2 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.

What are the valve clearances for the Toyota Corolla 1.3 16V?

Valve clearances for the Toyota Corolla 1.3 16V (1995–1997) are 0,15-0,25 mm inlet and 0,31-0,41 mm exhaust, measured cold.

What is the cylinder head torque for the Toyota Corolla 1.3 16V?

The cylinder head bolts on the Toyota Corolla 1.3 16V (1995–1997) are tightened in 3 stages: 22 Nm, then 44 Nm, then a final 90°.

What is the ignition timing for the Toyota Corolla 1.3 16V?

Basic ignition timing for the Toyota Corolla 1.3 16V (1995–1997) is 10° BTDC at 700 rpm.