Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity (Fiscal) cc | 1987 |
| Compression ratio :1 | 14,0 |
| Suitable for unleaded petrol | Yes |
| Minimum octane rating RON | 95 |
| Ignition system Make | Toyota |
| Ignition system Description | Map-DI |
| Trigger location | Cam/Crankshaft |
| Fuel system Make | Toyota |
| Fuel system Description | MFI-s(i+d) |
| Air metering Type | Mass |
| Combined ignition and fuel ECM | Yes |
| Diagnostic socket | Yes |
Ignition system
| Ignition coil supply voltage + with ballast V | 12,0 |
|---|
Firing order
The firing order for the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) is 1-3-4-2.
| Firing order | 1-3-4-2 |
|---|
Valve clearances
Valve clearances on the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) are hydraulic — they self-adjust, so no manual clearance figure applies.
| Valve clearance - INLET mm | Hydraulic |
|---|---|
| Valve clearance - EXHAUST mm | Hydraulic |
Engine oil & fluids
Engine oil
The Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) takes 4.3 litres of engine oil with the filter.
See the reference table for the complete engine oil entries and their conditions.
Coolant
See the reference table for the complete coolant entries and their conditions.
Grades, filling conditions and capacities
| Preferred engine oil | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-16 |
| Engine oil classification API/ACEA | SN |
| Engine oil options | |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-20 |
| Engine oil classification API/ACEA | SL |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 |
| Engine oil classification API/ACEA | SL |
| Ambient temperature range | -18°C➞ |
| Engine oil grade SAE | 10W-30 |
| Engine oil classification API/ACEA | SL |
| Ambient temperature range | -12°C➞ |
| Engine oil grade SAE | 15W-40 |
| Engine oil classification API/ACEA | SL |
| Engine with filter(s) litres | 4.3 |
| Other lubricants and capacities | |
| Automatic transmission fluid Type | Toyota ATF WS |
| Automatic transmission (drain & refill) litres | 3.6 |
| Do not drive vehicle in inspection mode as damage to the vehicle may occur. | |
| Coolant Type | Toyota SLLC |
| Coolant Colour | Pink |
| Cooling system - total capacity litres | 5.9 |
| Repeat steps 7-8 four times. | |
| Brake fluid Type | DOT 3/4 |
| Brake fluid litres | — |
Brakes & wear limits
Brake disc thickness
Brake discs on the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) are replaced at a minimum thickness of 25 mm (ventilated) front and 10,5 mm rear.
| Minimum disc thickness for replacement - ventilated Front | 25 mm |
|---|---|
| Minimum disc thickness for replacement Rear | 10,5 mm |
Brake disc and drum dimensions
| Disc runout Front | 0,05 mm |
|---|---|
| Disc runout Rear | 0,15 mm |
| Minimum pad thickness Front | 1 mm |
| Minimum pad thickness Rear | 1 mm |
Service & electrical
Battery
The Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) uses a 12 V, 45 Ah battery.
| Battery V/RC(Ah) | 12 (45) |
|---|
Spark plugs
The Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) uses Bosch 0 242 129 535 spark plugs with a 0,8 mm electrode gap.
| Spark plugs Original equipment | Denso |
|---|---|
| Spark plug Type | FC16HR-Q8 |
| Electrode gap mm | 0,7-0,8 |
| Spark plugs Make | Bosch |
| Spark plug Type | 0 242 129 535 |
| Electrode gap mm | 0,8 |
| Spark plugs Make | Champion |
| Spark plug Type | REA10WYPB |
| Electrode gap mm | 0,7 |
| Spark plugs Make | NGK |
| Spark plug Type | DILKAR6T8 |
| Electrode gap mm | 0,8 |
Tuning and emissions
| Tuning conditions | — |
|---|---|
| View more information | — |
| Ignition timing | |
| Ignition timing - basic BTDC °Engine/rpm | 10±2/1150±50 Not adjustable |
| Ignition advance checks °Engine/rpm | ECM Controlled |
| Idle speed rpm | 1100±50 Not adjustable |
| Oil temperature °C | 80 |
| CO level at idle speed - tailpipe Vol. % CO | 0,2 Max Not adjustable |
| HC level at idle speed ppm | 100 |
| CO2 level at idle speed Vol. % CO2 | 14,5-16 |
| O2 level at idle speed Vol. % O2 | 0,1-0,5 |
| Increased idle speed for CO test rpm | 2300-2700 |
| CO content at increased idle speed Vol. % | 0,2 |
| Lambda at increased idle λ | 0,97-1,03 |
Service checks and adjustments
| Compression pressure bar | 8,0-14,0 |
|---|---|
| Oil pressure bar/rpm | 0,8 Min |
| Radiator cap bar | 0,94-1,22 |
| Thermostat opens °C | 80-84 |
Fuel system
| System pressure bar | 3,0-6,4 |
|---|---|
| Fuel feed/lift pump delivery pressure bar | 2,0-8,3 |
| Fuel main pump delivery pressure bar | 24-195 |
| Engine coolant temperature (ECT) sensor Ohm/°C | 310-326/80 |
| Injector Ohm | 11,6-12,4 |
| Injector resistance | |
| Lambda sensor (Oxygen) heater Ohm | — |
| Lambda sensor (Oxygen) heater | |
| Throttle motor Ohm | 0,3-100 |
Tightening torques
Cylinder head bolt torque
The cylinder head bolts on the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) are tightened in 3 stages: 50 Nm, then 90°, then a final 90°.
| Cylinder head | |
|---|---|
| Tighten | 50 Nm |
| Tighten | 90° |
| Tighten | 90° |
| Cylinder head instructions | — |
|---|---|
| View more information | — |
| Other engine tightening torques | |
| Main bearings Renew bolts/nuts | — |
| View more information | — |
| Main bearings | |
| Main bearings Stage 1 | 61 Nm |
| Main bearings Stage 2 | 90° |
| Big end bearings Renew bolts/nuts | — |
| View more information | — |
| Big end bearings | |
| Big end bearings Stage 1 | 38 Nm |
| Big end bearings Stage 2 | 90° |
| Oil pump to cylinder block | 24 Nm |
| Sump bolts | — |
| View more information | — |
| Wait 2 hours before starting engine or filling engine with oil to allow sealant to dry. | |
| Sump drain bolt | 40 Nm |
| Flywheel/driveplate | -/150 Nm |
| After installing driveplate wait 1 hour before starting engine. | |
| Crankshaft pulley/damper centre bolt | 260 Nm |
| Camshaft sprocket/gear | — |
| Camshaft sprocket/gear | |
| Camshaft carrier/cap | — |
| View more information | — |
| Wait 2 hours before starting engine or filling engine with oil to allow sealant to dry. | |
| Camshaft/rocker cover | 8 Nm |
| View more information | — |
| Wait 2 hours before starting engine. | |
| Inlet manifold to cylinder head | 24 Nm |
| Exhaust manifold to cylinder head | 26 Nm |
| Exhaust downpipe to manifold | 43 Nm |
| Water pump | 43 Nm |
| Spark plugs | 20 Nm |
| Fuel rail | 29 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 10 Nm |
| Camshaft position (CMP) sensor | 8 Nm |
| Engine coolant temperature (ECT) sensor | 20 Nm |
| Lambda sensor (Oxygen) | 44 Nm |
| Knock sensor (KS) | 20 Nm |
| Engine oil pressure switch | 15 Nm |
| Assemble components within 3 minutes. Do not start engine for 1 hour. | |
| Oil filter | 18 Nm |
| Chassis tightening torques | |
| Front hub | 216 Nm |
| Front hub - wheel bearing housing bolts | 130 Nm |
| Rear hub - wheel bearing housing bolts | 90 Nm |
| Steering wheel | 50 Nm |
| Steering rack/box mounting | 133 Nm |
| Steering track rod end | 49 Nm |
| Steering track rod end | |
| Brake caliper to carrier Front | 32 Nm |
| Brake caliper to carrier | |
| Brake caliper/carrier to hub Front | 107 Nm |
| Brake caliper to carrier Rear | 35 Nm |
| Brake caliper/carrier to hub Rear | 107 Nm |
| ABS sensor Front | 9 Nm |
| ABS sensor Rear | 9 Nm |
| Road wheels | 103 Nm |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | No |
| Compressor variable displacement solenoid | Yes |
| Air conditioning refrigerant Type | R1234yf |
| Air conditioning refrigerant quantity grams | 470±30 |
| Air conditioning oil group | POE |
| Air conditioning oil Type | Dens Oil 11 |
| High voltage electric motor within compressor; correct oil must be used to reduce risk of electric shock. | |
| Air conditioning oil quantity cm³ | 117±7 |
| Air conditioning oil viscosity ISO | 46 |
Frequently asked questions
What is the firing order of the Toyota C-HR 2.0 Hybrid Synergy Drive?
The firing order for the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) is 1-3-4-2.
What spark plugs does the Toyota C-HR 2.0 Hybrid Synergy Drive use?
The Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) uses Bosch 0 242 129 535 spark plugs with a 0,8 mm electrode gap.
How much oil does the Toyota C-HR 2.0 Hybrid Synergy Drive take?
The Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) takes 4.3 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.
What are the valve clearances for the Toyota C-HR 2.0 Hybrid Synergy Drive?
Valve clearances on the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) are hydraulic — they self-adjust, so no manual clearance figure applies.
What is the cylinder head torque for the Toyota C-HR 2.0 Hybrid Synergy Drive?
The cylinder head bolts on the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) are tightened in 3 stages: 50 Nm, then 90°, then a final 90°.
What is the minimum brake disc thickness for the Toyota C-HR 2.0 Hybrid Synergy Drive?
Brake discs on the Toyota C-HR 2.0 Hybrid Synergy Drive (2019–2023) are replaced at a minimum thickness of 25 mm (ventilated) front and 10,5 mm rear.