Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity (Fiscal) cc | 1997 |
| Compression ratio :1 | 10,5 |
| Suitable for unleaded petrol | Yes |
| Minimum octane rating RON | 95 |
| Ignition system Make | Bosch |
| Ignition system Description | Map-DI |
| Trigger location | Cam/Crankshaft |
| Fuel system Make | Bosch |
| Fuel system Description | MFI-s(d) |
| Air metering Type | Mass/MAP |
| Combined ignition and fuel ECM | Yes |
| Diagnostic socket | Yes |
Ignition system
| Ignition coil Make | Land Rover |
|---|---|
| Ignition coil Type | LR091616 |
| Ignition coil supply voltage + with ballast V | 12,0 |
Firing order
The firing order for the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) is 1-3-4-2.
| Firing order | 1-3-4-2 |
|---|
Valve clearances
Valve clearances on the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) are hydraulic — they self-adjust, so no manual clearance figure applies.
| Valve clearance - INLET mm | Hydraulic |
|---|---|
| Valve clearance - EXHAUST mm | Hydraulic |
Engine oil & fluids
Engine oil
The Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) takes 7.02 litres of engine oil with the filter. The specified engine oil grade is SAE 0W-20 for all ambient temperatures, with oil specification STJLR.03.5006.
Transfer box
The transfer box has a listed capacity of 0.4 litres.
See the reference table for the complete transfer box entries and their conditions.
Coolant
The listed coolant type is Havoline XLC. The recorded coolant colour is Orange. The listed total cooling-system capacity is 11.45 litres.
Cooling system must be filled using vacuum filling equipment.
Grades, filling conditions and capacities
| Engine oil options | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-20 |
| Engine oil classification OEM | STJLR.03.5006 |
| Engine with filter(s) litres | 7.02 |
| Other lubricants and capacities | |
| Automatic transmission fluid Type | Shell L12108 (ZF Lifeguard 8) |
| Automatic transmission (drain & refill) litres | — |
| Filling transmission and checking ATF level | |
| Automatic transmission (dry fill) litres | 6.5 |
| Automatic transmission - dry fill capacity | |
| Differential oil grade - rear SAE | 75W-80 Castrol BOT 799 |
| Differential rear litres | 0.8 |
| Rear differential oil | |
| Transfer box oil grade SAE | 75W-90 Castrol BOT 750 PLUS |
| Transfer box litres | 0.4 |
| Transfer box oil | |
| Coolant Type | Havoline XLC |
| Coolant Colour | Orange |
| Cooling system - total capacity litres | 11.45 |
| Cooling system must be filled using vacuum filling equipment. | |
| Brake fluid Type | DOT 4 LV |
| Brake fluid classification | ISO Class 6 |
Brakes & wear limits
Brake disc thickness
Rear brake discs on the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) are replaced at a minimum thickness of 8 mm or 18 mm (ventilated).
| Minimum disc thickness for replacement - ventilated Front | — |
|---|---|
| Minimum disc thickness for replacement - ventilated front | |
| Minimum disc thickness for replacement Rear | 8 mm |
| Minimum disc thickness for replacement - ventilated Rear | 18 mm |
Brake disc and drum dimensions
| Minimum disc thickness for replacement - ventilated front | |
|---|---|
| Minimum pad thickness Front | 3 mm |
| Minimum pad thickness Rear | 3 mm |
Service & electrical
Ignition timing
The ignition timing on the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) is not adjustable.
| Ignition timing - basic BTDC °Engine/rpm | Not adjustable |
|---|
Spark plugs
The Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) uses Bosch 0 242 140 566 spark plugs with a 0,7 mm electrode gap.
| Spark plugs Original equipment | Land Rover |
|---|---|
| Spark plug Type | H4P3-12405 (ACA) |
| Electrode gap mm | 0,60-0,65 |
| Spark plugs Make | Bosch |
| Spark plug Type | 0 242 140 566 |
| Electrode gap mm | 0,7 |
| Spark plugs Make | NGK |
| Spark plug Type | SILZKAR8G7Y |
| Electrode gap mm | 0,7 |
Tuning and emissions
| Ignition advance checks °Engine/rpm | ECM Controlled |
|---|---|
| Idle speed rpm | Not adjustable |
| CO level at idle speed - tailpipe Vol. % CO | Not adjustable |
Starting and charging
| Battery V/RC(Ah) | 12 |
|---|
Fuel system
| Fuel main pump delivery pressure bar | 200 Max |
|---|
Tightening torques
| Cylinder head instructions | — |
|---|---|
| Cylinder head | |
| Renew bolts | Yes |
| Other engine tightening torques | |
| Main bearings Renew bolts/nuts | Yes |
| Main bearings Stage 1 | — |
| Main bearings | |
| Big end bearings Renew bolts/nuts | Yes |
| Big end bearings Stage 1 | 20 Nm |
| Big end bearings Stage 2 | 125° |
| Oil pump to cylinder block | 25 Nm |
| Sump bolts | — |
| View more information | — |
| Assemble components and tighten bolts within 7 minutes. | |
| Sump drain bolt | 25 Nm |
| Flywheel/driveplate | -/30 Nm+120° |
| Crankshaft pulley/damper bolts | 37 Nm+90° |
| Camshaft sprocket/gear | 25 Nm+60° |
| Camshaft carrier/cap | — |
| View more information | — |
| If new cylinder head fitted, use tool No. 303-1444-02. If re-using cylinder head, use tool No. 303-1444-01. | |
| Inlet manifold to cylinder head | 12 Nm |
| Exhaust manifold to cylinder head | 1)10 Nm 2)25 Nm |
| Exhaust downpipe to manifold | 18 Nm |
| Water pump | 1)6 Nm 2)12 Nm |
| Spark plugs | 23 Nm |
| View more information | — |
| Spark plugs | |
| Fuel rail | 1)20 Nm 2)30 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 8 Nm |
| Camshaft position (CMP) sensor | 8 Nm |
| Lambda sensor (Oxygen) | 48 Nm |
| Knock sensor (KS) | 20 Nm |
| Oil filter | 28 Nm |
| Chassis tightening torques | |
| Front hub | — |
| Front/rear hub | |
| Rear hub | — |
| Steering wheel | 47 Nm |
| Steering rack/box mounting | 30 Nm+60° |
| Steering track rod end | 133 Nm |
| Brake disc to hub Front | 10 Nm |
| Brake caliper to carrier Front | 58 Nm |
| Brake caliper to carrier | |
| Brake caliper/carrier to hub Front | 110 Nm+120° |
| Brake disc to hub Rear | 10 Nm |
| Brake caliper to carrier Rear | 30 Nm |
| Brake caliper/carrier to hub Rear | 110 Nm |
| Back plate to hub Rear | 10 Nm |
| ABS sensor Front | 9 Nm |
| ABS sensor Rear | 9 Nm |
| Road wheels | 1)4 Nm 2)70 Nm 3)133 Nm |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | Yes |
| Air conditioning refrigerant Type | — |
| Do not mix R134a with R1234yf. | |
| Air conditioning refrigerant quantity grams | 525±10 |
| Air conditioning oil group | PAG |
| Air conditioning oil Type | SPA2 |
| Air conditioning oil quantity cm³ | 110 |
Frequently asked questions
What is the firing order of the Land Rover Range Rover Evoque 2.0 P250 MHEV?
The firing order for the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) is 1-3-4-2.
What spark plugs does the Land Rover Range Rover Evoque 2.0 P250 MHEV use?
The Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) uses Bosch 0 242 140 566 spark plugs with a 0,7 mm electrode gap.
How much oil does the Land Rover Range Rover Evoque 2.0 P250 MHEV take?
The Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) takes 7.02 litres of engine oil with the filter. The specified engine oil grade is SAE 0W-20 for all ambient temperatures, with oil specification STJLR.03.5006.
What are the valve clearances for the Land Rover Range Rover Evoque 2.0 P250 MHEV?
Valve clearances on the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) are hydraulic — they self-adjust, so no manual clearance figure applies.
What is the ignition timing for the Land Rover Range Rover Evoque 2.0 P250 MHEV?
The ignition timing on the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) is not adjustable.
What is the minimum brake disc thickness for the Land Rover Range Rover Evoque 2.0 P250 MHEV?
Rear brake discs on the Land Rover Range Rover Evoque 2.0 P250 MHEV (2019–2026) are replaced at a minimum thickness of 8 mm or 18 mm (ventilated).