Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity cc | 1597 |
Injection system
| Air metering Type | Mass/MAP |
|---|---|
| Pump type | Common rail |
Injection sequence
The injection sequence for the Honda HR-V 1.6 i-DTEC (2015–2018) is 1-3-4-2.
| Injection sequence | 1-3-4-2 |
|---|
Valve clearances
Valve clearances on the Honda HR-V 1.6 i-DTEC (2015–2018) are hydraulic — they self-adjust, so no manual clearance figure applies.
| Valve clearance - INLET mm | Hydraulic |
|---|---|
| Valve clearance - EXHAUST mm | Hydraulic |
Engine oil & fluids
Engine oil
The Honda HR-V 1.6 i-DTEC (2015–2018) takes 4.7 litres of engine oil with the filter.
See the reference table for the complete engine oil entries and their conditions.
Manual gearbox
The manual gearbox has a listed capacity of 1.9 litres. The manual gearbox capacity for dry fill is 2.0 litres.
See the reference table for the complete manual gearbox entries and their conditions.
Coolant
The listed total cooling-system capacity is 4.5 litres.
See the reference table for the complete coolant entries and their conditions.
Grades, filling conditions and capacities
| Preferred engine oil | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil classification OEM | 08232-P99D1/4LHE |
| Engine oil options | |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-30 Synthetic |
| Engine oil classification API/ACEA | /C2, C3 |
| Engine with filter(s) litres | 4.7 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | Honda MTF III |
| Manual transmission litres | 1.9 |
| Manual transmission (dry fill) litres | 2.0 |
| Coolant Type | Honda all season type 2 |
| Cooling system - total capacity litres | 4.5 |
| Brake fluid Type | DOT 4 |
| Clutch fluid Type | DOT 4 |
Brakes & wear limits
Brake disc thickness
Brake discs on the Honda HR-V 1.6 i-DTEC (2015–2018) are replaced at a minimum thickness of 23 mm (ventilated) front and 8 mm rear.
| Minimum disc thickness for replacement - ventilated Front | 23 mm |
|---|---|
| Minimum disc thickness for replacement Rear | 8 mm |
Brake disc and drum dimensions
| Disc thickness variation Front | 0,015 mm |
|---|---|
| Disc thickness variation Rear | 0,015 mm |
| Disc runout Front | 0,04 mm |
| Disc runout Rear | 0,04 mm |
| Minimum pad thickness Front | 1,6 mm |
| Minimum pad thickness Rear | 1,6 mm |
Service & electrical
Tuning and emissions
| Idle speed rpm | 800±50 |
|---|
Service checks and adjustments
| Compression pressure bar | 15,0 Min |
|---|---|
| Oil pressure bar/rpm | 3,5/3000 |
| Radiator cap bar | 0,93-1,23 |
| Thermostat opens °C | 86-90 |
Tightening torques
| Cylinder head instructions | — |
|---|---|
| View more information | — |
| Other engine tightening torques | |
| Sump drain bolt | 40 Nm |
| Flywheel/driveplate | 118 Nm/- |
| Clutch pressure plate | 26 Nm |
| Crankshaft pulley/damper centre bolt | — |
| Camshaft sprocket/gear | 24 Nm |
| Camshaft carrier/cap | — |
| View more information | — |
| Wait 30 minutes before filling engine with oil and do not run engine for 3 hours. | |
| Camshaft/rocker cover | 10 Nm |
| Injector/clamp | 6 Nm+180° |
| Injector pipe unions | 33 Nm |
| Glow plugs | 14 Nm |
| Oil filter | 12 Nm |
| Chassis tightening torques | |
| Front hub | 328 Nm |
| Rear hub - wheel bearing housing bolts | 64 Nm |
| Steering wheel | 49 Nm |
| Steering track rod end | 54 Nm |
| Brake disc to hub Front | 10 Nm |
| Brake caliper to carrier Front | 50 Nm |
| Brake caliper/carrier to hub Front | 108 Nm |
| Brake disc to hub Rear | 10 Nm |
| Brake caliper to carrier Rear | 35 Nm |
| Brake caliper/carrier to hub Rear | 108 Nm |
| Back plate to hub Rear | 10 Nm |
| ABS sensor Front | 10 Nm |
| ABS sensor Rear | 10 Nm |
| Road wheels | 108 Nm |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | No |
| Air conditioning refrigerant Type | R1234yf |
| Air conditioning refrigerant quantity grams | 420±25 |
| Air conditioning oil group | POE |
| Air conditioning oil Type | Dens Oil 14 |
| Air conditioning oil quantity cm³ | 76±6 |
Frequently asked questions
What is the injection sequence of the Honda HR-V 1.6 i-DTEC?
The injection sequence for the Honda HR-V 1.6 i-DTEC (2015–2018) is 1-3-4-2.
How much oil does the Honda HR-V 1.6 i-DTEC take?
The Honda HR-V 1.6 i-DTEC (2015–2018) takes 4.7 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.
What are the valve clearances for the Honda HR-V 1.6 i-DTEC?
Valve clearances on the Honda HR-V 1.6 i-DTEC (2015–2018) are hydraulic — they self-adjust, so no manual clearance figure applies.
What is the minimum brake disc thickness for the Honda HR-V 1.6 i-DTEC?
Brake discs on the Honda HR-V 1.6 i-DTEC (2015–2018) are replaced at a minimum thickness of 23 mm (ventilated) front and 8 mm rear.