Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity cc | 2199 |
| Compression ratio :1 | 16,3 |
Injection system
| Air metering Type | Mass |
|---|---|
| Pump type | Common rail |
Injection sequence
The injection sequence for the Honda Accord 2.2 i-DTEC (2008–2015) is 1-3-4-2.
| Injection sequence | 1-3-4-2 |
|---|
Valve clearances
Valve clearances on the Honda Accord 2.2 i-DTEC (2008–2015) are hydraulic — they self-adjust, so no manual clearance figure applies.
| Valve clearance - INLET mm | Hydraulic |
|---|---|
| Valve clearance - EXHAUST mm | Hydraulic |
Engine oil & fluids
Engine oil
The Honda Accord 2.2 i-DTEC (2008–2015) takes 5.5 litres of engine oil with the filter.
See the reference table for the complete engine oil entries and their conditions.
Manual gearbox
The manual gearbox has a listed capacity of 2.2 litres.
See the reference table for the complete manual gearbox entries and their conditions.
Coolant
See the reference table for the complete coolant entries and their conditions.
Grades, filling conditions and capacities
| Engine oil options | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 0W-30 Synthetic |
| Engine oil classification API/ACEA | /C2, C3 |
| Engine with filter(s) litres | 5.5 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | Honda MTF |
| Manual transmission litres | 2.2 |
| Automatic transmission fluid Type | Honda ATF-Z1 |
| Automatic transmission (drain & refill) litres | 2.6 |
| If replacement of ATF was not due, transmission oil change indicator can only be reset using diagnostic equipment. | |
| Automatic transmission (dry fill) litres | 8.2 |
| Coolant Type | Honda all season type 2 |
| Cooling system - total capacity litres | 6.9 |
| Brake fluid Type | DOT 3/4 |
Brakes & wear limits
Brake disc thickness
Brake discs on the Honda Accord 2.2 i-DTEC (2008–2015) are replaced at a minimum thickness of 23 mm (ventilated) front and 8 mm rear.
| Minimum disc thickness for replacement - ventilated Front | 23 mm |
|---|---|
| Minimum disc thickness for replacement Rear | 8 mm |
| Maximum drum diameter for replacement Rear | 191 mm |
Brake disc and drum dimensions
| Disc thickness variation Front | 0,015 mm |
|---|---|
| Disc thickness variation Rear | 0,015 mm |
| Disc runout Front | 0,04 mm |
| Disc runout Rear | 0,04 mm |
| Minimum pad thickness Front | 1,5 mm |
| Minimum pad thickness Rear | 1,6 mm |
| Minimum shoe thickness Rear | 1 mm |
| Parking brake travel No. of notches | 6-7 |
Service & electrical
Battery
The Honda Accord 2.2 i-DTEC (2008–2015) uses a 12 V, 70 Ah battery.
| Battery V/RC(Ah) | 12 (70) |
|---|
Tuning and emissions
| Idle speed rpm | 820±50 |
|---|---|
| Oil temperature °C | 80 |
| Idle speed - for smoke test rpm | 670-770 |
| Governed speed range - for smoke test rpm | 4200-4500 |
| Maximum time at governed speed secs | 1,8 |
| Test mode A/B | B |
| Probe type 1/2 | 1 |
| Conditioning Accelerations/rpm | /3000 |
| Smoke opacity - EU limit m-1 (%) | 1,50 (47) |
| Smoke opacity - homologation value m-1 (%) | 1,50 (47) |
Service checks and adjustments
| Compression pressure bar | 24,0 Min |
|---|---|
| Oil pressure bar/rpm | 4,1/3000 |
| Radiator cap bar | 1,12-1,46 |
| Thermostat opens °C | 76-80 |
Tightening torques
| Cylinder head instructions | — |
|---|---|
| View more information | — |
| Other engine tightening torques | |
| Main bearings Renew bolts/nuts | No |
| Main bearings Stage 1 | — |
| View more information | — |
| Big end bearings Stage 1 | 20 Nm |
| View more information | — |
| Big end bearings Stage 2 | 90° |
| Oil pump to cylinder block | 45 Nm |
| Sump bolts | 12 Nm |
| Sump drain bolt | 39 Nm |
| Flywheel/driveplate | 118 Nm |
| Clutch pressure plate | 25 Nm |
| Crankshaft pulley/damper centre bolt | — |
| Camshaft sprocket/gear | 120 Nm |
| Camshaft carrier/cap | — |
| View more information | — |
| Wait 30 minutes before filling engine with oil and do not run engine for 3 hours. | |
| Camshaft/rocker cover | 10 Nm |
| View more information | — |
| Inlet manifold to cylinder head | 22 Nm |
| Exhaust manifold to cylinder head | 45 Nm |
| Exhaust downpipe to manifold | 33 Nm |
| Water pump | 12 Nm |
| Injector/clamp | 5 Nm+90° |
| Injector pipe unions | 33 Nm |
| Fuel/injection pump mounting | 22 Nm |
| Glow plugs | 20 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 12 Nm |
| Camshaft position (CMP) sensor | 12 Nm |
| Engine coolant temperature (ECT) sensor | 12 Nm |
| Engine oil pressure switch | 18 Nm |
| Oil filter | 25 Nm |
| Chassis tightening torques | |
| Front hub | 328 Nm |
| Rear hub - wheel bearing housing bolts | 98 Nm |
| Steering wheel | 39 Nm |
| Steering track rod end | 54 Nm |
| Brake disc to hub Front | 10 Nm |
| Brake caliper to carrier Front | 28 Nm |
| Brake caliper/carrier to hub Front | 108 Nm |
| Brake disc to hub Rear | 10 Nm |
| Brake caliper to carrier Rear | 23 Nm |
| Brake caliper/carrier to hub Rear | 108 Nm |
| Road wheels | 108 Nm |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | No |
| Air conditioning refrigerant Type | R134a |
| Air conditioning refrigerant quantity grams | 475±25 |
| Air conditioning oil group | PAG |
| Air conditioning oil Type | Dens Oil 8 |
| Air conditioning oil quantity cm³ | 105 |
| Air conditioning oil viscosity ISO | 46 |
Frequently asked questions
What is the injection sequence of the Honda Accord 2.2 i-DTEC?
The injection sequence for the Honda Accord 2.2 i-DTEC (2008–2015) is 1-3-4-2.
How much oil does the Honda Accord 2.2 i-DTEC take?
The Honda Accord 2.2 i-DTEC (2008–2015) takes 5.5 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.
What are the valve clearances for the Honda Accord 2.2 i-DTEC?
Valve clearances on the Honda Accord 2.2 i-DTEC (2008–2015) are hydraulic — they self-adjust, so no manual clearance figure applies.
What is the minimum brake disc thickness for the Honda Accord 2.2 i-DTEC?
Brake discs on the Honda Accord 2.2 i-DTEC (2008–2015) are replaced at a minimum thickness of 23 mm (ventilated) front and 8 mm rear.
What battery does the Honda Accord 2.2 i-DTEC use?
The Honda Accord 2.2 i-DTEC (2008–2015) uses a 12 V, 70 Ah battery.