Honda1998–2003

Accord 2.0: Common faults & known problems

Common faults & known problems

5 known faults documented in workshop bulletins. Of these, two concern the engine and fuel system and one the electrical and ignition. Symptoms, causes, repair steps and part numbers are shown where supplied.

Engine & fuel system

2 documented faults — symptoms, causes and workshop fixes.

Poor engine performance

Affects All models with VTEC engine.

Symptoms

Engine malfunction indicator lamp (MIL) illuminated. Trouble codes stored in engine control module (ECM) fault memory: 22-4.

Cause

Engine oil level incorrect.

Oil supply pressure to variable valve timing (VVT) system too low.

Repair

  1. Top up engine oil to correct level.

Data: Motorwise Workshop. Bulletin 2.

Poor starting

Affects All models.

Symptoms

Excessive fuel consumption. Poor engine running.

Cause

Poor connection between battery earth lead and chassis earth point due to corrosion.

Repair

  1. Inspect earth lead for corrosion, replace if necessary.

Data: Motorwise Workshop. Bulletin 3.

Electrical & ignition

1 documented fault — symptoms, causes and workshop fixes.

Radio interference

Overview

Affects
All models.
Remedy
Fit modified part

Cause

Poor earth connection on roof aerial base.

Signal interference from alternator.

Repair steps

  1. Clean and check earth connection on roof aerial base.
  2. Fit modified aerial base nut.
  3. Tighten aerial base nut. Tightening torque: 4.5 - 5.0 Nm.

Parts

Parts listed in the bulletin
PartPart numberQty
Aerial base nut39153-S6A-J011

Data: Motorwise Workshop. Bulletin 4.

Suspension & drivetrain

1 documented fault — symptoms, causes and workshop fixes.

Knocking noise from front wheel when pulling away

Overview

Affects
All models, 1982-05.
Remedy
Clean & lubricate

Cause

Contact between driveshaft and front wheel bearing.

Repair

  1. Clean driveshaft and wheel bearing contact surfaces.
  2. Apply grease to contact surfaces of driveshaft and wheel bearing.

Data: Motorwise Workshop. Bulletin 5.

Clutch & gearbox

1 documented fault — symptoms, causes and workshop fixes.

Noise from clutch release bearing, more noticeable on cold start

Affects All models with manual transmission, →VIN U100001.Fit modified part

Cause

Insufficient slave cylinder spring load.

Repair

  1. Fit modified slave cylinder.
Parts1 part
Parts listed in the bulletin
PartPart numberQty
Slave cylinder46930 SN7 0001

Data: Motorwise Workshop. Bulletin 1.

Glossary

Technical terms used in this guide.

MIL
Malfunction indicator lamp — the engine warning light on the dashboard
ECM
Engine control module — the electronic unit that manages the engine
VIN
Vehicle identification number — 17 characters, found at the base of the windscreen and on the V5C logbook
Nm
Newton-metres — the standard unit for how tightly a bolt is done up
Trouble Codes
Standardised fault codes stored by the engine control module, read with a diagnostic tool
Control Module
A control unit for one of the vehicle's systems (engine, gearbox, brakes, body, and so on)
Driveshaft
The shaft that takes drive from the differential out to a wheel
Fault Memory
The list of stored trouble codes in a control module
Alternator
The unit that charges the battery while the engine is running
Earth
An electrical ground connection back to the battery or body

Frequently asked questions

What are the common faults with the Honda Accord 2.0?

This guide contains five workshop bulletins for the Honda Accord 2.0. Of these, two concern the engine and fuel system and one the electrical and ignition. Symptoms, causes, repair steps and part numbers are shown where supplied.

Does every Honda Accord 2.0 have these faults?

No. These are patterns documented across the model by workshops, not predictions for an individual vehicle. Where a fault applies only to certain vehicles or VIN ranges, that is listed with the fault.

Can I check for Honda Accord 2.0 faults myself?

Many of them. The documented symptoms can be seen, heard or felt during a test drive.

Related guides

Glossary term

See in the glossary →