Toyota1992–1994Technical specifications

Carina E 2.0 GTi: Technical specifications

Workshop data for the 2-litre petrol (engine code 3S-GE). Covers engine, fluids, brakes, service, torques and air conditioning: the figures to check before a job or a parts order.

Summary

Match the engine code (3S-GE) to the vehicle before ordering parts or applying these figures.

Vehicle specifications

Overview

Make: Toyota
Model: Carina E
Years: 1992–1994
Fuel: Petrol
Engine code: 3S-GE

Performance & efficiency

Power: 116 kW (158 hp)
Engine size: 1,998 cc
Cylinders: 4 · DOHC
Compression ratio: 10.0:1
Fuel system: Toyota

Fluids & capacities

Engine oil (with the filter): 4.3 litres

All 123 specifications below

Engine & identification

Vehicle identification

No. of cylinders Type	4/DOHC
Capacity (Fiscal) cc	1998
Compression ratio :1	10,0
Suitable for unleaded petrol	Yes
Minimum octane rating RON	95
Ignition system Type	ESA
Ignition system Description	Map-i
Trigger location	Distributor
Fuel system Make	Toyota
Fuel system Type	TCCS
Fuel system Description	MFI-i
Air metering Type	MAP
Combined ignition and fuel ECM	Yes
Diagnostic socket	Yes

Ignition system

Ignition coil Make	Denso
Ignition coil supply voltage + with ballast V	12,0
Primary resistance Ohm	0,4-0,5
Secondary resistance Ohm	10000-14000
Distributor (ECM) Make	Toyota
Contact breaker gap/trigger air gap mm	0,2-0,4

Firing order

The firing order for the Toyota Carina E 2.0 GTi (1992–1994) is 1-3-4-2.

Firing order	1-3-4-2

Valve clearances

Valve clearances for the Toyota Carina E 2.0 GTi (1992–1994) are 0,15-0,25 mm inlet and 0,20-0,30 mm exhaust, measured cold.

Valve clearance - INLET mm	0,15-0,25 cold
Valve clearance - EXHAUST mm	0,20-0,30 cold

Engine oil & fluids

Engine oil

The Toyota Carina E 2.0 GTi (1992–1994) takes 4.3 litres of engine oil with the filter.

See the reference table for the complete engine oil entries and their conditions.

Manual gearbox

The manual gearbox has a listed capacity of 2.6 litres. The specified oil is Dexron II.

Coolant

The listed total cooling-system capacity is 6.6 litres.

Grades, filling conditions and capacities

Lubricants and capacities — complete reference
Engine oil options
Ambient temperature range	-29°C➞10°C
Engine oil grade SAE	5W-30
Engine oil classification API/ACEA	SH/A1
Ambient temperature range	-18°C➞38°C
Engine oil grade SAE	10W-30
Engine oil classification API/ACEA	SH/A1
Ambient temperature range	-12°C➞38°C
Engine oil grade SAE	15W-40
Engine oil classification API/ACEA	SH/A2
Ambient temperature range	-12°C➞38°C
Engine oil grade SAE	20W-50
Engine oil classification API/ACEA	SH/A2
Engine with filter(s) litres	4.3
Other lubricants and capacities
Manual transmission oil grade SAE	Dexron II
Manual transmission litres	2.6
Cooling system - total capacity litres	6.6
Brake fluid Type	DOT 3
Power steering fluid Type	Dexron II
Power steering fluid litres	0.8

Brakes & wear limits

Brake disc thickness

Brake discs on the Toyota Carina E 2.0 GTi (1992–1994) are replaced at a minimum thickness of 23 mm (ventilated) front and 9 mm rear.

Minimum disc thickness for replacement - ventilated Front	23 mm
Minimum disc thickness for replacement Rear	9 mm

Brake disc and drum dimensions

Disc runout Front	0,05 mm
Disc runout Rear	0,15 mm
Minimum pad thickness Front	1 mm
Minimum pad thickness Rear	1 mm
Parking brake travel No. of notches	4-7

Service & electrical

Ignition timing

Basic ignition timing for the Toyota Carina E 2.0 GTi (1992–1994) is 10° BTDC at 850 rpm.

Ignition timing
Ignition timing - basic BTDC °Engine/rpm	10/850

Battery

The Toyota Carina E 2.0 GTi (1992–1994) uses a 12 V, 40 Ah battery (reserve capacity 60 minutes).

Battery V/RC(Ah)	12/60 (40)

Spark plugs

The Toyota Carina E 2.0 GTi (1992–1994) uses NGK BKR6EP-8 spark plugs with a 0,8 mm electrode gap.

Spark plugs Original equipment	NGK
Spark plug Type	BKR6EP-8
Electrode gap mm	0,8
Spark plugs Make	Bosch
Spark plug Type	FR5DP1X
Electrode gap mm	1,1
Spark plugs Make	NGK
Spark plug Type	BKR6EP-8
Electrode gap mm	0,8

Tuning and emissions

Ignition timing
Tuning conditions	—
View more information	—
Ignition advance checks °Engine/rpm	ECM Controlled
Idle speed rpm	800±50 Not adjustable
Oil temperature °C	80
CO level at idle speed - tailpipe Vol. % CO	0,5 Max Not adjustable
HC level at idle speed ppm	100
CO2 level at idle speed Vol. % CO2	14,5-16
O2 level at idle speed Vol. % O2	0,1-0,5
Increased idle speed for CO test rpm	2400-2600
CO content at increased idle speed Vol. %	0,3
Lambda at increased idle λ	0,98-1,02

Starting and charging

Starter motor Make	Denso
Starter motor Type	1,2 kW
Minimum starting voltage V	11,5
Maximum cranking amps A	108-132
Alternator Make	Nippon Denso
Alternator output A/V/rpm	30/13,5/2000
Voltage regulator Type	IC
Regulated voltage V	13,5-15,0

Service checks and adjustments

Compression pressure bar	10,0-12,5
Oil pressure bar/rpm	2,5-5,0/3000
Radiator cap bar	0,75-1,05
Thermostat opens °C	80-84

Fuel system

System pressure bar	2,7-3,1
Regulated pressure with vacuum bar	2,1-2,6
Engine coolant temperature (ECT) sensor Ohm/°C	250-400/80
Crankshaft position (CKP) sensor/engine speed (RPM) sensor Ohm	140-180
Injector Ohm	13,8
Idle air control (IAC) valve/idle speed control (ISC) actuator Ohm	19,0-22,3
Lambda sensor (Oxygen) heater Ohm	5,0-6,3

Tightening torques

Cylinder head bolt torque

The cylinder head bolts on the Toyota Carina E 2.0 GTi (1992–1994) are tightened in 3 stages: 25 Nm, then 49 Nm, then a final 90°.

Cylinder head
Renew bolts	No
Tighten	25 Nm
Tighten	49 Nm
Tighten	90°

Other engine tightening torques
Cylinder head instructions	—
Main bearings Renew bolts/nuts	No
Main bearings Stage 1	30 Nm
Main bearings Stage 2	59 Nm
Big end bearings Renew bolts/nuts	No
Big end bearings Stage 1	34 Nm
Big end bearings Stage 2	67 Nm
Oil pump to cylinder block	21 Nm
Sump bolts	5 Nm
Flywheel/driveplate	108 Nm
Clutch pressure plate	19 Nm
Crankshaft pulley/damper centre bolt	108 Nm
Camshaft sprocket/gear	59 Nm
Camshaft carrier/cap	19 Nm
Camshaft/rocker cover	3 Nm
Spark plugs	18 Nm
Chassis tightening torques
Front hub	226 Nm
Rear hub	123 Nm
Steering track rod end	49 Nm
Brake caliper to carrier Front	34 Nm
Brake caliper/carrier to hub Front	94 Nm
Brake caliper to carrier Rear	20 Nm
Brake caliper/carrier to hub Rear	47 Nm
ABS sensor Front	8 Nm
ABS sensor Rear	8 Nm
Road wheels	103 Nm

Air conditioning

Oil type
Air conditioning refrigerant Type	R134a
Air conditioning refrigerant quantity grams	750±50
Air conditioning oil group	PAG
Air conditioning oil Type	Dens Oil 8
Air conditioning oil quantity cm³	—
Air conditioning oil viscosity ISO	46

Frequently asked questions

What is the firing order of the Toyota Carina E 2.0 GTi?

The firing order for the Toyota Carina E 2.0 GTi (1992–1994) is 1-3-4-2.

What spark plugs does the Toyota Carina E 2.0 GTi use?

The Toyota Carina E 2.0 GTi (1992–1994) uses NGK BKR6EP-8 spark plugs with a 0,8 mm electrode gap.

How much oil does the Toyota Carina E 2.0 GTi take?

The Toyota Carina E 2.0 GTi (1992–1994) takes 4.3 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.

What are the valve clearances for the Toyota Carina E 2.0 GTi?

Valve clearances for the Toyota Carina E 2.0 GTi (1992–1994) are 0,15-0,25 mm inlet and 0,20-0,30 mm exhaust, measured cold.

What is the cylinder head torque for the Toyota Carina E 2.0 GTi?

The cylinder head bolts on the Toyota Carina E 2.0 GTi (1992–1994) are tightened in 3 stages: 25 Nm, then 49 Nm, then a final 90°.

What is the ignition timing for the Toyota Carina E 2.0 GTi?

Basic ignition timing for the Toyota Carina E 2.0 GTi (1992–1994) is 10° BTDC at 850 rpm.