Engine & identification
Vehicle identification
| No. of cylinders Type | 4/DOHC |
|---|---|
| Capacity cc | 2198 |
| Compression ratio :1 | 15,5 |
Injection system
| Air metering Type | Mass/MAP |
|---|---|
| Pump type | Common rail |
Injection sequence
The injection sequence for the Land Rover Defender 2.2 TD4 (2011–2016) is 1-3-4-2.
| Injection sequence | 1-3-4-2 |
|---|
Valve clearances
Valve clearances on the Land Rover Defender 2.2 TD4 (2011–2016) are hydraulic — they self-adjust, so no manual clearance figure applies.
| Valve clearance - INLET mm | Hydraulic |
|---|---|
| Valve clearance - EXHAUST mm | Hydraulic |
Engine oil & fluids
Engine oil
The Land Rover Defender 2.2 TD4 (2011–2016) takes 6.9 litres of engine oil with the filter.
A listed engine oil option is SAE 5W-30 synthetic for all ambient temperatures, with oil specification WSS-M2C934-B.
A listed engine oil option is SAE 5W-30 for all ambient temperatures, with oil specification WSS-M2C913-B.
A listed engine oil option is SAE 5W-30 for all ambient temperatures, with oil specification WSS-M2C913-C.
Manual gearbox
The manual gearbox has a listed capacity of 2.2 litres. The manual gearbox capacity for dry fill is 2.4 litres. The specified oil is SAE 75W-90 synthetic, with classification WSD-M2C200-C.
Transfer box
The transfer box has a listed capacity of 2.3 litres. The specified oil is SAE 75W-90, with classification GL-5.
Coolant
The listed coolant type is WAS-M97B44-D. The recorded coolant colour is Orange. The listed total cooling-system capacity is 8.2 litres.
Grades, filling conditions and capacities
| Engine oil options | |
|---|---|
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 Synthetic |
| Engine oil classification OEM | WSS-M2C934-B |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 |
| Engine oil classification OEM | WSS-M2C913-B |
| Ambient temperature range | All temperatures |
| Engine oil grade SAE | 5W-30 |
| Engine oil classification OEM | WSS-M2C913-C |
| Engine with filter(s) litres | 6.9 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | 75W-90 Synthetic |
| Manual transmission oil classification | WSD-M2C200-C |
| Manual transmission litres | 2.2 |
| Manual transmission (dry fill) litres | 2.4 |
| Differential oil grade - front SAE | 80W-90, 85W-90 |
| Differential oil classification - front | GL-5 |
| Differential front/AT litres | 1.7 |
| Differential oil grade - rear SAE | 80W-90, 85W-90 |
| Differential rear litres | — |
| Transfer box oil grade SAE | 75W-90 |
| Transfer box oil classification | GL-5 |
| Transfer box litres | 2.3 |
| Coolant Type | WAS-M97B44-D |
| Coolant Colour | Orange |
| Cooling system - total capacity litres | 8.2 |
| Brake fluid Type | Shell DOT 4 ESL |
| Clutch fluid Type | Super DOT 4 |
| Clutch fluid classification | ESD-M6C57-A |
| Power steering fluid Type | — |
| Power steering fluid litres | 1.6 |
Brakes & wear limits
Brake disc thickness
Brake discs on the Land Rover Defender 2.2 TD4 (2011–2016) are replaced at a minimum thickness of 12,1 mm (solid) or 22 mm (ventilated) front and 11,7 mm rear.
| Minimum disc thickness for replacement - solid Front | 12,1 mm |
|---|---|
| Minimum disc thickness for replacement - ventilated Front | 22 mm |
| Minimum disc thickness for replacement Rear | 11,7 mm |
Brake disc and drum dimensions
| Disc runout Front | 0,15 mm |
|---|---|
| Disc runout Rear | 0,15 mm |
| Minimum pad thickness Front | 3 mm |
| Minimum pad thickness Rear | 3 mm |
Service & electrical
Starting and charging
| Battery V/RC(Ah) | 12 |
|---|
Service checks and adjustments
| Oil pressure bar/rpm | 2,0/2000 |
|---|---|
| Radiator cap bar | 1,00 |
| Thermostat opens °C | 82-96 |
Tightening torques
| Cylinder head instructions | — |
|---|---|
| Cylinder head | |
| Renew bolts | Yes |
| Other engine tightening torques | |
| Oil pump to cylinder block | 10 Nm |
| Sump bolts | 1)7 Nm 2)14 Nm |
| View more information | — |
| Sump drain bolt | 23 Nm |
| Flywheel/driveplate | — |
| Clutch pressure plate | 29 Nm |
| Crankshaft pulley/damper bolts | — |
| Camshaft sprocket/gear | 35 Nm |
| Camshaft carrier/cap | — |
| View more information | — |
| Camshaft/rocker cover | 1)4 Nm 2)11 Nm |
| Rocker shaft | 10 Nm+45° |
| Inlet manifold to cylinder head | 15 Nm |
| Exhaust manifold to cylinder head | 1)15 Nm 2)35 Nm |
| Water pump | 23 Nm |
| Injector/clamp | 6 Nm+360° |
| Injector pipe unions | 1)15 Nm 2)30 Nm |
| Fuel/injection pump sprocket/gear | 64 Nm |
| Fuel/injection pump mounting | 23 Nm |
| Glow plugs | 13 Nm |
| Engine oil pressure switch | 15 Nm |
| Oil filter | 35 Nm |
| Chassis tightening torques | |
| Front hub | 1)30 Nm 2)210 Nm |
| Rear hub | 1)30 Nm 2)210 Nm |
| Steering wheel | 43 Nm |
| Steering track rod end | 40 Nm |
| Brake disc to hub Front | 73 Nm |
| Brake caliper/carrier to hub Front | 82 Nm |
| Brake disc to hub Rear | 73 Nm |
| Brake caliper/carrier to hub Rear | 82 Nm |
| Road wheels | — |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | No |
| Air conditioning refrigerant Type | R134a |
| Air conditioning refrigerant quantity grams | 600±25 |
| Air conditioning oil group | PAG |
| Air conditioning oil Type | SP10 |
| Air conditioning oil quantity cm³ | 130 |
| Air conditioning oil viscosity ISO | 46 |
Frequently asked questions
What is the injection sequence of the Land Rover Defender 2.2 TD4?
The injection sequence for the Land Rover Defender 2.2 TD4 (2011–2016) is 1-3-4-2.
How much oil does the Land Rover Defender 2.2 TD4 take?
The Land Rover Defender 2.2 TD4 (2011–2016) takes 6.9 litres of engine oil with the filter. A listed engine oil option is SAE 5W-30 synthetic for all ambient temperatures, with oil specification WSS-M2C934-B. A listed engine oil option is SAE 5W-30 for all ambient temperatures, with oil specification WSS-M2C913-B. A listed engine oil option is SAE 5W-30 for all ambient temperatures, with oil specification WSS-M2C913-C.
What are the valve clearances for the Land Rover Defender 2.2 TD4?
Valve clearances on the Land Rover Defender 2.2 TD4 (2011–2016) are hydraulic — they self-adjust, so no manual clearance figure applies.
What is the minimum brake disc thickness for the Land Rover Defender 2.2 TD4?
Brake discs on the Land Rover Defender 2.2 TD4 (2011–2016) are replaced at a minimum thickness of 12,1 mm (solid) or 22 mm (ventilated) front and 11,7 mm rear.