Engine & identification
Vehicle identification
| No. of cylinders Type | 4/OHC |
|---|---|
| Capacity (Fiscal) cc | 1343 |
| Compression ratio :1 | 9,2 |
| Suitable for unleaded petrol | Yes |
| Minimum octane rating RON | 95 |
| Ignition system Make | Honda |
| Ignition system Description | Map-i |
| Trigger location | Distributor |
| Fuel system Make | Honda |
| Fuel system Type | PGM-FI |
| Fuel system Description | MFI-s |
| Air metering Type | MAP |
| Combined ignition and fuel ECM | Yes |
| Diagnostic socket | Yes |
Ignition system
| Ignition coil supply voltage + with ballast V | 12 |
|---|
Firing order
The firing order for the Honda Logo 1.3 (1999–2002) is 1-3-4-2.
| Firing order | 1-3-4-2 |
|---|
Valve clearances
Valve clearances for the Honda Logo 1.3 (1999–2002) are 0,18-0,22 mm inlet and 0,25-0,29 mm exhaust, measured cold.
| Valve clearance - INLET mm | 0,18-0,22 cold |
|---|---|
| Valve clearance - EXHAUST mm | 0,25-0,29 cold |
Engine oil & fluids
Engine oil
The Honda Logo 1.3 (1999–2002) takes 3.6 litres of engine oil with the filter.
See the reference table for the complete engine oil entries and their conditions.
Manual gearbox
The manual gearbox has a listed capacity of 1.9 litres. The specified oil is SAE 10W-30.
Coolant
The listed total cooling-system capacity is 4.7 litres.
Grades, filling conditions and capacities
| Engine oil options | |
|---|---|
| Ambient temperature range | ➞35°C |
| Engine oil grade SAE | 5W-30 |
| Engine oil classification API/ACEA | SJ/A2 |
| Ambient temperature range | -20°C➞35°C |
| Engine oil grade SAE | 10W-30 |
| Engine oil classification API/ACEA | SJ/A2 |
| Ambient temperature range | -20°C➞ |
| Engine oil grade SAE | 10W-40 |
| Engine oil classification API/ACEA | SJ/A2 |
| Ambient temperature range | -15°C➞ |
| Engine oil grade SAE | 15W-40, 15W-50 |
| Engine oil classification API/ACEA | SJ/A2 |
| Ambient temperature range | -10°C➞ |
| Engine oil grade SAE | 20W-40, 20W-50 |
| Engine oil classification API/ACEA | SJ/A2 |
| Engine with filter(s) litres | 3.6 |
| Other lubricants and capacities | |
| Manual transmission oil grade SAE | 10W-30 |
| Manual transmission litres | 1.9 |
| Automatic transmission fluid Type | Honda CVT |
| Automatic transmission (drain & refill) litres | 2.8 |
| Automatic transmission (dry fill) litres | 5.4 |
| Cooling system - total capacity litres | 4.7 |
| Brake fluid Type | DOT 3/4 |
| Power steering fluid Type | Honda PAS |
| Power steering fluid litres | 0.6 |
Brakes & wear limits
Brake disc thickness
Brake discs on the Honda Logo 1.3 (1999–2002) are replaced at a minimum thickness of 19 mm (ventilated) front; the rear brake drums are replaced at a maximum diameter of 201 mm.
| Minimum disc thickness for replacement - ventilated Front | 19 mm |
|---|---|
| Maximum drum diameter for replacement Rear | 201 mm |
Brake disc and drum dimensions
| Disc thickness variation Front | 0,015 mm |
|---|---|
| Disc runout Front | 0,10 mm |
| Minimum pad thickness Front | 1,6 mm |
| Minimum shoe thickness Rear | 2 mm |
| Parking brake travel No. of notches | 7-10 |
Service & electrical
Ignition timing
Basic ignition timing for the Honda Logo 1.3 (1999–2002) is 8°±2° BTDC at 750 rpm.
| Ignition timing - basic BTDC °Engine/rpm | 8±2/750 |
|---|
Battery
The Honda Logo 1.3 (1999–2002) uses a 12 V, 36 Ah battery.
| Battery V/RC(Ah) | 12 (36) |
|---|
Tuning and emissions
| Ignition advance checks °Engine/rpm | ECM Controlled |
|---|---|
| Idle speed rpm | 750±50 |
| Oil temperature °C | 80 |
| CO level at idle speed - tailpipe Vol. % CO | 0,1 Max Not adjustable |
| HC level at idle speed ppm | 100 |
| CO2 level at idle speed Vol. % CO2 | 14,5-16 |
| O2 level at idle speed Vol. % O2 | 0,1-0,5 |
| Increased idle speed for CO test rpm | 2300-2700 |
| CO content at increased idle speed Vol. % | 0,3 |
| Lambda at increased idle λ | 0,98-1,02 |
Starting and charging
| Alternator output A/V/rpm | 70/13,5/650-750 |
|---|
Service checks and adjustments
| Compression pressure bar | 9,5 Min |
|---|---|
| Oil pressure bar/rpm | 3,5/3000 |
| Radiator cap bar | 0,95-1,25 |
| Thermostat opens °C | 76-80 |
Fuel system
| System pressure bar | 2,3-2,8 |
|---|---|
| Regulated pressure with vacuum bar | 1,65-2,15 |
| Engine coolant temperature (ECT) sensor Ohm/°C | 250-300/90 |
| Injector Ohm | 10,0-13,0 |
| Lambda sensor (Oxygen) heater Ohm | 10,0-40,0 |
Spark plugs
| Spark plugs Original equipment | NGK |
|---|---|
| Spark plug Type | ZFR5F-11 |
| Electrode gap mm | 1,0-1,1 |
| Spark plugs Make | NGK |
| Spark plug Type | ZFR5F-11 |
| Electrode gap mm | 1,0-1,1 |
Tightening torques
Cylinder head bolt torque
The cylinder head bolts on the Honda Logo 1.3 (1999–2002) are tightened in 4 stages: 20 Nm, then 49 Nm, then 67 Nm, then a final 67 Nm.
| Cylinder head | |
|---|---|
| Renew bolts | No |
| Tighten | 20 Nm |
| Tighten | 49 Nm |
| Tighten | 67 Nm |
| Tighten | 67 Nm |
| Cylinder head instructions | — |
|---|---|
| Other engine tightening torques | |
| Main bearings Renew bolts/nuts | No |
| Main bearings Stage 1 | 25 Nm |
| Main bearings Stage 2 | 44 Nm |
| Big end bearings Renew bolts/nuts | No |
| Big end bearings Stage 1 | 15 Nm |
| Big end bearings Stage 2 | 31 Nm |
| Oil pump to cylinder block | 10 Nm |
| Sump bolts | 12 Nm |
| Sump drain bolt | 44 Nm |
| Flywheel/driveplate | 118 Nm |
| Clutch pressure plate | 25 Nm |
| Crankshaft pulley/damper centre bolt | 20 Nm+90° |
| Camshaft sprocket/gear | 37 Nm |
| Camshaft carrier/cap | — |
| Camshaft carrier/cap | |
| Camshaft/rocker cover | 10 Nm |
| Inlet manifold to cylinder head | 24 Nm |
| Exhaust manifold to cylinder head | 31 Nm |
| Exhaust downpipe to manifold | 22 Nm |
| Spark plugs | 18 Nm |
| Fuel rail | 12 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 12 Nm |
| Engine coolant temperature (ECT) sensor | 18 Nm |
| Lambda sensor (Oxygen) | 44 Nm |
| Engine oil pressure switch | 18 Nm |
| Chassis tightening torques | |
| Front hub | 181 Nm |
| Rear hub | 152 Nm |
| Steering track rod end | 44 Nm |
| Brake disc to hub Front | 10 Nm |
| Brake caliper to carrier Front | 23 Nm |
| Brake caliper/carrier to hub Front | 108 Nm |
| ABS sensor Front | 10 Nm |
| Road wheels | 108 Nm |
Air conditioning
| No. of AC service connectors | 2 |
|---|---|
| Air conditioning restrictor type | Expansion valve |
| Compressor clutch/magnetic coupling | Yes |
| Compressor variable displacement solenoid | No |
| Air conditioning refrigerant Type | R134a |
| Air conditioning refrigerant quantity grams | 525±25 |
| Air conditioning oil Type | — |
Frequently asked questions
What is the firing order of the Honda Logo 1.3?
The firing order for the Honda Logo 1.3 (1999–2002) is 1-3-4-2.
How much oil does the Honda Logo 1.3 take?
The Honda Logo 1.3 (1999–2002) takes 3.6 litres of engine oil with the filter. See the reference table for the complete engine oil entries and their conditions.
What are the valve clearances for the Honda Logo 1.3?
Valve clearances for the Honda Logo 1.3 (1999–2002) are 0,18-0,22 mm inlet and 0,25-0,29 mm exhaust, measured cold.
What is the cylinder head torque for the Honda Logo 1.3?
The cylinder head bolts on the Honda Logo 1.3 (1999–2002) are tightened in 4 stages: 20 Nm, then 49 Nm, then 67 Nm, then a final 67 Nm.
What is the ignition timing for the Honda Logo 1.3?
Basic ignition timing for the Honda Logo 1.3 (1999–2002) is 8°±2° BTDC at 750 rpm.
What is the minimum brake disc thickness for the Honda Logo 1.3?
Brake discs on the Honda Logo 1.3 (1999–2002) are replaced at a minimum thickness of 19 mm (ventilated) front; the rear brake drums are replaced at a maximum diameter of 201 mm.