Mercedes-Benz C-Class 2013: reliability & common MOT faults

In 2025, 69 in every 100 first MOTs on a 2013 Mercedes-Benz C-Class were passes. Most common reason for a fail: Suspension arm ball joint (front).

Summary

A 2013 Mercedes-Benz C-Class passed first time about 2 in every 100 less often than the average of the 2012 and 2014 model years.

At a glance

How 22,380 first tests went in 2025.

Passed first time
69 in every 100
Did not pass first time
31 in every 1006,855 failed first-attempt tests
The typical car
12 yearsabout 98,356 miles
First tests counted
22,380

What failed most often

  1. Suspension arm ball joint (front)19 in every 100 failed tests
  2. Handbrake efficiency below minimum (roller test)14 in every 100 failed tests
  3. Anti-roll bar linkage ball joint dust cover (front)10 in every 100 failed tests

How we count this. Data: UK MOT open data, 2025. Only Class 4 cars on their first MOT of the year are counted. A car that fails and is fixed at the test station still counts as a fail in the first-attempt rate. These are raw results, not adjusted for age, mileage, or peer mix. The MOT does not test engine or gearbox internals.

Note:

These are patterns across 2013 Mercedes-Benz C-Class vehicles in 2025, not a prediction that any one car will have them. Faults are grouped by part of the car. A wear pattern follows age and use more than the way the car was built. They come from MOT defect codes, not manufacturer bulletins, recalls or a diagnosis of any one car.

Suspension

Four faults. The strongest is the suspension sub-frame (rear): 17 times as often as on similar cars.

Figures below are measured across the 6,848 of 6,855 failed first attempts (99.9%) that recorded an odometer reading in 2025. Mileage is needed to compare like with like.

We only list faults with at least 20 failures and a rate of about 2.0 times that of similar cars, which keeps one-off results out of the list.

Suspension sub-frame (rear)

Failed on 202 first tests17 times as often as similar carsStrong evidence

What it means

A suspension sub-frame insecurely attached to the chassis or axle is Major, and Dangerous when it is insecure and impairing directional stability. A sub-frame that is missing, likely to become detached, fractured or likely to fail is also Dangerous. Excessive damage or corrosion that seriously weakens it is Major.

Anti-roll bar ball joint dust cover (front)

Failed on 317 first tests3.5 times as often as similar carsLikely evidence

What it means

A missing anti-roll bar ball joint dust cover is Major, and so is one that no longer prevents the ingress of dirt. A cover that is only severely deteriorated is Minor. DVSA uses one wording for the dust cover on any suspension joint.

Anti-roll bar linkage ball joint dust cover (front)

Failed on 690 first tests2.9 times as often as similar carsPossible evidence

What it means

A suspension joint dust cover that is severely deteriorated is Minor. It becomes Major once it is missing or no longer prevents the ingress of dirt, so what matters is whether it still keeps dirt out. DVSA words this for any suspension joint dust cover, and files it here under anti-roll bars.

Suspension arm ball joint (front)

Failed on 1,316 first tests2.7 times as often as similar carsPossible evidence

What it means

A suspension arm ball joint is failed under the general suspension pin, bush or joint wording. Excessively worn is Major, and likely to become detached is graded Dangerous.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage.

Brakes

Four faults. The strongest is the handbrake lever: 4.8 times as often as on similar cars.

Handbrake lever

Failed on 252 first tests4.8 times as often as similar carsLikely evidence

What it means

A parking brake lever pivot or ratchet mechanism that is obviously worn is graded Minor. It is Major when worn to the extent that the brake may inadvertently release, and also when the ratchet is not holding correctly. A lever must have obvious excessive travel before being rejected.

Also noted as an advisory

Testers also noted it as an advisory, worn but not yet failing, on 47 first tests, 8.1 times as often as on similar cars.

Anti-lock braking system (ABS)

Failed on 341 first tests3.9 times as often as similar carsLikely evidence

What it means

ABS is failed as removed only where it has obviously been removed, because not every vehicle in the age range where removal is not permitted has ABS. A warning lamp that does not light or shows an ABS fault is Major, as is a missing or excessively damaged wheel speed sensor. Every failure row for this component is Major.

Electronic stability control

Failed on 194 first tests3.3 times as often as similar carsLikely evidence

What it means

An ESC warning lamp is failed only when the tester is certain it indicates an ESC malfunction, because the lamp takes various forms and the owner's handbook may need checking. The system is also called ESP, VDC or DSC, among many other names. Every failure row is Major, covering the lamp, wheel speed sensors, wiring, other components and the switch.

Handbrake efficiency below minimum (roller test)

Failed on 985 first tests2.9 times as often as similar carsPossible evidence

What it means

A parking brake with efficiency below the minimum requirement is Major, and graded Dangerous where efficiency is less than half of the required value. On a roller brake tester, the requirement counts as met if more than half of the wheels of a brake system lock. The check applies only to vehicles whose parking brake was not already tested as the secondary brake.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage. Advisories count notes recorded on failed first tests only.

Tyres

One wear pattern: tyre tread depth (rear), 2.7 times as often as on similar cars.

Tyre tread depth (rear)

Failed on 583 first tests2.7 times as often as similar carsWear pattern

What it means

Only primary grooves count when tread depth is assessed: those holding the wear indicators, or cut as deep as those when new. Shallower secondary grooves are ignored. Tread depth below the minimum for the vehicle is Dangerous, and so is a pattern not visible over the whole tread, but that second row applies only to vehicles that need the lower minimum.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage.

Noise, emissions and leaks

One fault: diesel engine warning light, 2.6 times as often as on similar cars.

Diesel engine warning light

Failed on 422 first tests2.6 times as often as similar carsPossible evidence

What it means

An engine malfunction indicator lamp that is illuminated to show a malfunction is graded Major on a diesel, but only on the diesels the test covers, which depends on the vehicle type and when it was first used. DVSA lists it under exhaust emissions for compression ignition engines, and the detail line for the row also names an inoperative lamp.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage.

Advisories

Other things testers noted as worn or close to failing, more often than on similar cars.

An advisory is a note from the tester about something that has not failed yet. It is an early warning, not a fail. Advisories for the faults above are shown with those faults.

Wheel bearings (front)

Noted on 547 first tests11 times as often as similar carsElevated evidence

Rigid brake pipes (front)

Noted on 359 first tests2.3 times as often as similar carsElevated evidence

Handbrake efficiency on trikes, quads and pre-1968 vehicles (roller test)

Noted on 23 first tests2.3 times as often as similar carsElevated evidence

Data: UK MOT open data, 2025. Counts cover advisories recorded on failed first tests only, compared with cars of the same age and mileage.

MOT pass rates

How first tests ended, and how the pass rates are counted.

Passed first time
69in every 100
Passed on the first test.
Fixed at the station
4in every 100
Failed, then fixed at the test station the same day.
Failed
27in every 100
Did not pass, and were not fixed at the test station.

First-attempt pass 69.4% of 22,380 first tests (2025): only cars that passed first time count. Official-style pass 73.2%: cars fixed at the test station also count as a pass. The 4 fixed and the 27 not fixed make the 31 in every 100 that did not pass first time.

Petrol and diesel

First testsTypical mileagePassed first time, as testedPassed first time, same mileage
Diesel16,670106,353 miles6768
Petrol5,70974,564 miles7671

Figures are in every 100 first tests. Cars with more miles usually fail more often, so the same-mileage figure gives every fuel the mileage mix of all the cars in this year.

Same model, other years

Passed first time in every 100, all tested in 2025.

40608010020002005201020132020Older carsNewer cars
4060801002000201020132020Older carsNewer cars

Newer cars are younger, so look for a jump rather than the climb. A year earlier (2024), when these cars were a year younger, 70 in every 100 passed first time.

YearPassed first timeFirst tests
199672 in every 100347
199768 in every 100584
199871 in every 100723
199968 in every 100644
200066 in every 100501
200164 in every 1001,041
200263 in every 1001,935
200358 in every 1003,438
200458 in every 1005,099
200559 in every 1006,889
200658 in every 1008,303
200761 in every 10010,849
200863 in every 10012,485
200964 in every 10011,974
201066 in every 10012,159
201167 in every 10017,849
201267 in every 10024,448
2013 This car69 in every 10022,380
201475 in every 10024,165
201578 in every 10032,615
201680 in every 10034,859
201781 in every 10037,580
201884 in every 10026,966
201985 in every 10023,530
202086 in every 1009,433
202187 in every 1005,769
202289 in every 1004,378

If you are buying one

What this year's MOT record means for the decision in front of you.

Mileage matters most on a 2013 C-Class.

Of 2013 C-Class vehicles with under 69,000 miles, 81 in every 100 passed their 2025 MOT first time. With 132,000 miles or more, 62 in every 100 did.

Under 69,0004,430 tests
81
69,000–89,0004,421 tests
72
89,000–108,000 Typical car4,613 tests
68
108,000–132,0004,381 tests
65
132,000 and over4,521 tests
62

Petrol or diesel?

Typical mileagePassed first time,
as tested
Passed first time,
same mileage
Diesel106,353 miles6768
Petrol74,564 miles7671

Figures are in every 100 first tests. Petrol cars look better on the raw figures only because diesel cars have done more miles (typically 106,353 against 74,564). At the same mileage there is no clear difference between the two.


What to check at your mileage

How often each fault turned up on a failed first test, by the car's mileage. Read it as: what is likely to need looking at on a car like the one in front of you.

Under 69,00089,000–108,000132,000 and over
Suspension arm ball joint (front)1.45.810.1
Handbrake efficiency below minimum (roller test)1.54.36.8
Anti-roll bar linkage ball joint dust cover (front)1.33.54.1
Tyre condition (front)2.13.32.9
Tyre tread depth (rear)0.92.73.4

Faults per 100 first tests, by the car's mileage at the test.


When a car fails

37in every 100

of failed cars had one item to fix.

35in every 100

of failed cars had three or more items to fix.

9in every 100

of all first tests had a defect the tester marked dangerous (unsafe to drive away).


Every figure here is a first-attempt MOT rate from DVSA open data for this model line, for cars of this model year tested in 2025. Each mileage band holds a fifth of the tests. MOTs do not test engine or gearbox internals, so this is a pre-purchase checklist, not a full reliability score.

FAQs

Short answers about how to read this model-year guide.

A 2013 Mercedes-Benz C-Class passed first time about 2 in every 100 less often than the average of the 2012 and 2014 model years. In 2025, 69.4% of 22,380 first MOTs on the 2013 Mercedes-Benz C-Class passed first time (PRS: items fixed at the station the same day, counted as a fail). The official-style rate including PRS is 73.2%. Among 6,855 failed first-attempt MOT tests (test year 2025), Suspension sub-frame (rear) appears more often than on similar cars (2.9% of those tests; 202 observed failures; about 17× more often than similar cars). There is no single reliability score here; this is a pre-purchase checklist built from DVSA open data, not a guarantee for any individual car.
Ranked by how often they were actually recorded, the items that most often failed a 2013 Mercedes-Benz C-Class at the first attempt were Suspension arm ball joint (front) (19.2%), Handbrake efficiency below minimum (roller test) (14.4%) and Anti-roll bar linkage ball joint dust cover (front) (10.1%), each as a share of the year's failed first attempts. That is what goes wrong most often on the car. The common faults table shows a different measure: faults that are unusual compared with similar cars.
Among failed first-attempt tests we highlight patterns that appear more often than on similar cars. Top example: Suspension sub-frame (rear) (2.9% of those tests; 202 observed failures; about 17× more often than similar cars). These are statistical signals, not a diagnosis of any individual car.
Suspension sub-frame (rear) shows up more often than on similar cars (2.9% of those tests; 202 observed failures; about 17× more often than similar cars). That does not prove a design fault. Age, mileage, and how the car was used still matter. Treat it as a pre-purchase checkpoint, not a manufacturer service bulletin.
Common MOT problem areas for the 2013 Mercedes-Benz C-Class include Suspension sub-frame (rear), Handbrake lever, Anti-lock braking system (ABS). These are the faults that stand out compared with similar cars, not a complete list of what can go wrong on any individual car.
Advisories flag issues noted at the test and are not a fail rate. We show advisory patterns that appear more often than on similar cars among failed first-attempt tests, separate from common failure rows. Use them as early-warning checks, not as a pass/fail score.
This page highlights MOT failure patterns for the 2013 Mercedes-Benz C-Class (registration year) using UK DVSA open data for the selected test year. Patterns are compared with cars of a similar age and mileage. It is a buyer checklist from MOT defect statistics, not a full service history or manufacturer service-bulletin list.
No. MOT tests do not cover engine internals, gearboxes, or many electronic modules. Patterns here come from MOT defect statistics only and should not be read as engine or gearbox reliability scores.

About this data

How this page is built and what it can (and can't) say.

These figures come from UK MOT open data for this model year. We surface common failure patterns against similar cars, not a full reliability score, and not a pass/fail verdict on any individual vehicle.

2024 2025

What we include

UK Class 4 cars only. Normal MOT tests (not retests); first test per vehicle per calendar year; results pass, PRS, or fail.

Same-day repairs

PRS means the car failed items that were fixed at the test station and then passed the same day. We count PRS as a first-attempt fail in headline rates so same-day repairs do not hide problems.

How we compare

We compare this model year with other Class 4 cars of similar age and mileage in the same test year. This model family is left out of the peer group so the car is not measured against itself.

What this does not cover

  • MOTs do not cover engine internals, gearboxes, or many electronics; this is not a full reliability score.
  • Common faults come from MOT defect stats, not manufacturer TSBs or recalls.
  • Age and mileage matching reduces, but does not remove, differences in how cars were used and maintained.
  • If the data for a car is too thin to say anything useful, we say so rather than guess.

Contains public sector information licensed under the Open Government Licence v3.0.

Check any vehicle’s MOT history

Full MOT history, mileage records, and reliability insights for any UK vehicle.

Run a free check