Ford Transit Connect 2007: reliability & common MOT faults

In 2025, 47 in every 100 first MOTs on a 2007 Ford Transit Connect were passes. Most common reason for a fail: Drive shaft joints and boots (front).

Summary

The 2007 Ford Transit Connect follows the pattern of the model years either side.

At a glance

How 5,865 first tests went in 2025.

Passed first time
47 in every 100
Did not pass first time
53 in every 1003,080 failed first-attempt tests
The typical car
18 yearsabout 143,159 miles
First tests counted
5,865

What failed most often

  1. Drive shaft joints and boots (front)19 in every 100 failed tests
  2. Suspension mounting area (rear)16 in every 100 failed tests
  3. Individual sidelight or tail light (front)12 in every 100 failed tests

How we count this. Data: UK MOT open data, 2025. Only Class 4 cars on their first MOT of the year are counted. A car that fails and is fixed at the test station still counts as a fail in the first-attempt rate. These are raw results, not adjusted for age, mileage, or peer mix. The MOT does not test engine or gearbox internals.

Note:

These are patterns across 2007 Ford Transit Connect vehicles in 2025, not a prediction that any one car will have them. Faults are grouped by part of the car. They come from MOT defect codes, not manufacturer bulletins, recalls or a diagnosis of any one car.

Seat belts and restraints

One fault: seat belt mounting area (front), 13 times as often as on similar cars.

Figures below are measured across the 3,056 of 3,080 failed first attempts (99.2%) that recorded an odometer reading in 2025. Mileage is needed to compare like with like.

We only list faults with at least 20 failures and a rate of about 2.0 times that of similar cars, which keeps one-off results out of the list.

Seat belt mounting area (front)

Failed on 257 first tests13 times as often as similar carsStrong evidence

What it means

A seat belt anchorage likely to become detached in the event of a collision is graded Dangerous. The load bearing structure near an anchorage, called a prescribed area, is Major when its strength or continuity is significantly reduced or it is inadequately repaired. Anchorage points are inspected for all seat belts fitted, except a belt with no corresponding seat.

Also noted as an advisory

Testers also noted it as an advisory, worn but not yet failing, on 42 first tests, 6.0 times as often as on similar cars.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage. Advisories count notes recorded on failed first tests only.

Body and structure

Three faults. The strongest is the vehicle structure condition (rear): 11 times as often as on similar cars.

Vehicle structure condition (rear)

Failed on 170 first tests11 times as often as similar carsStrong evidence

What it means

Structure that is fractured, deformed, corroded, modified or inadequately repaired is failed on rigidity only if the overall structural rigidity of the vehicle is significantly reduced. Structure that is likely to affect steering or braking adversely is graded Dangerous. Prescribed areas are not covered here, as they are checked under other sections, including brakes and steering.

Also noted as an advisory

Testers also noted it as an advisory, worn but not yet failing, on 134 first tests, 3.5 times as often as on similar cars.

Chassis condition (rear)

Failed on 112 first tests9.4 times as often as similar carsStrong evidence

What it means

A main load-bearing structural member that is fractured, deformed, modified or inadequately repaired is Major when structural rigidity is significantly reduced, and Dangerous where steering or braking is likely to be adversely affected. Corrosion of the body, cab or chassis at a mounting point is Dangerous where overall security or stability is impaired.

Vehicle structure condition (front)

Failed on 64 first tests3.0 times as often as similar carsLikely evidence

What it means

Structure that is fractured, deformed, corroded, modified or inadequately repaired is failed on rigidity only if the overall structural rigidity of the vehicle is significantly reduced. Structure that is likely to affect steering or braking adversely is graded Dangerous. Prescribed areas are not covered here, as they are checked under other sections, including brakes and steering.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage. Advisories count notes recorded on failed first tests only.

Brakes

Two faults. The strongest is the rigid brake pipes (front): 4.3 times as often as on similar cars.

Rigid brake pipes (front)

Failed on 169 first tests4.3 times as often as similar carsLikely evidence

What it means

Chafing, corrosion or damage to a rigid brake pipe justifies rejection once its wall thickness is reduced by a set amount, although DVSA accepts this is not easy to determine. If a tester is not sure, the benefit of the doubt applies. A leaking pipe or connection is graded Dangerous on a hydraulic system and Major on an air system.

Also noted as an advisory

Testers also noted it as an advisory, worn but not yet failing, on 526 first tests, 4.6 times as often as on similar cars.

Brake efficiency below minimum (roller test)

Failed on 66 first tests3.2 times as often as similar carsLikely evidence

What it means

Service brake efficiency below the minimum requirement is Major, and efficiency less than half of the required value is graded Dangerous. On a roller brake tester, if more than half of the wheels of a brake system lock, the efficiency requirement for that system counts as met.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage. Advisories count notes recorded on failed first tests only.

Suspension

Two faults. The strongest is the suspension mounting area (rear): 3.8 times as often as on similar cars.

Suspension mounting area (rear)

Failed on 498 first tests3.8 times as often as similar carsLikely evidence

What it means

The load bearing structure within a set distance of a sub-frame, spring or suspension component mounting is a prescribed area. Major applies when its strength or continuity is significantly reduced or it is inadequately repaired. Dangerous applies when it is so weakened that control of the vehicle is likely to be adversely affected.

Wheel bearings (front)

Failed on 182 first tests3.8 times as often as similar carsLikely evidence

What it means

Excessive play in a wheel bearing, or a bearing that is excessively rough, is Major. Play so excessive that the bearing is likely to break up or directional control is impaired is Dangerous, and so is a bearing so rough that it is likely to overheat or break up.

Also noted as an advisory

Testers also noted it as an advisory, worn but not yet failing, on 96 first tests, 2.1 times as often as on similar cars.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage. Advisories count notes recorded on failed first tests only.

Noise, emissions and leaks

Two faults. The strongest is the diesel emissions not tested: 3.7 times as often as on similar cars.

Diesel emissions not tested

Failed on 87 first tests3.7 times as often as similar carsLikely evidence

What it means

An emissions test on a diesel that is unable to be completed is graded Major. The failure wording 'not tested' carries the same Major grade.

Diesel engine warning light

Failed on 134 first tests2.7 times as often as similar carsPossible evidence

What it means

An engine malfunction indicator lamp that is illuminated to show a malfunction is graded Major on a diesel, but only on the diesels the test covers, which depends on the vehicle type and when it was first used. DVSA lists it under exhaust emissions for compression ignition engines, and the detail line for the row also names an inoperative lamp.

Data: UK MOT open data, 2025. Compared with cars of the same age and mileage.

Advisories

Other things testers noted as worn or close to failing, more often than on similar cars.

An advisory is a note from the tester about something that has not failed yet. It is an early warning, not a fail. Advisories for the faults above are shown with those faults.

Brake pedal

Noted on 145 first tests8.6 times as often as similar carsPossible evidence

Other power steering components

Noted on 61 first tests4.3 times as often as similar carsElevated evidence

Brake light (rear)

Noted on 106 first tests3.7 times as often as similar carsElevated evidence

Suspension mounting area

Noted on 68 first tests3.5 times as often as similar carsStrong evidence

Coil spring (front)

Noted on 276 first tests2.9 times as often as similar carsElevated evidence

Data: UK MOT open data, 2025. Counts cover advisories recorded on failed first tests only, compared with cars of the same age and mileage.

MOT pass rates

How first tests ended, and how the pass rates are counted.

Passed first time
47in every 100
Passed on the first test.
Fixed at the station
9in every 100
Failed, then fixed at the test station the same day.
Failed
44in every 100
Did not pass, and were not fixed at the test station.

First-attempt pass 47.5% of 5,865 first tests (2025): only cars that passed first time count. Official-style pass 55.5%: cars fixed at the test station also count as a pass. The 9 fixed and the 44 not fixed make the 53 in every 100 that did not pass first time.

Same model, other years

Passed first time in every 100, all tested in 2025.

4060801002007201020152020Older carsNewer cars
406080100200720102020Newer cars

Newer cars are younger, so look for a jump rather than the climb. A year earlier (2024), when these cars were a year younger, 46 in every 100 passed first time.

YearPassed first timeFirst tests
200348 in every 1001,656
200448 in every 1002,349
200548 in every 1003,332
200646 in every 1004,900
2007 This car47 in every 1005,865
200848 in every 1005,473
200948 in every 1003,846
201049 in every 1004,020
201153 in every 1004,794
201253 in every 1004,871
201358 in every 1003,796
201465 in every 1009,833
201568 in every 10012,339
201670 in every 10013,126
201774 in every 10017,395
201875 in every 10015,680
201973 in every 10014,001
202073 in every 10010,444
202179 in every 10010,665
202279 in every 1007,683

If you are buying one

What this year's MOT record means for the decision in front of you.

Mileage makes a modest difference on a 2007 Transit Connect.

Of 2007 Transit Connect vehicles with under 107,000 miles, 53 in every 100 passed their 2025 MOT first time. With 179,000 miles or more, 46 in every 100 did.

Under 107,0001,154 tests
53
107,000–133,0001,205 tests
46
133,000–154,000 Typical car1,132 tests
47
154,000–179,0001,148 tests
45
179,000 and over1,183 tests
46

What to check at your mileage

How often each fault turned up on a failed first test, by the car's mileage. Read it as: what is likely to need looking at on a car like the one in front of you.

Under 107,000133,000–154,000179,000 and over
Drive shaft joints and boots (front)9.710.29.7
Suspension mounting area (rear)7.39.07.7
Individual sidelight or tail light (front)3.47.07.2
Brake light5.06.65.8
Handbrake efficiency below minimum (roller test)2.76.47.3

Faults per 100 first tests, by the car's mileage at the test.


When a car fails

14in every 100

of failed cars had one item to fix.

70in every 100

of failed cars had three or more items to fix.

14in every 100

of all first tests had a defect the tester marked dangerous (unsafe to drive away).


Every figure here is a first-attempt MOT rate from DVSA open data for this model line, for cars of this model year tested in 2025. Each mileage band holds a fifth of the tests. MOTs do not test engine or gearbox internals, so this is a pre-purchase checklist, not a full reliability score.

FAQs

Short answers about how to read this model-year guide.

The 2007 Ford Transit Connect follows the pattern of the model years either side. Its main cause of failure was Drive shaft joints and boots (front), about 19 in every 100 failed tests. In 2025, 47.5% of 5,865 first MOTs on the 2007 Ford Transit Connect passed first time (PRS: items fixed at the station the same day, counted as a fail). The official-style rate including PRS is 55.5%. Among 3,080 failed first-attempt MOT tests (test year 2025), Seat belt mounting area (front) appears more often than on similar cars (8.4% of those tests; 257 observed failures; about 13× more often than similar cars). There is no single reliability score here; this is a pre-purchase checklist built from DVSA open data, not a guarantee for any individual car.
Ranked by how often they were actually recorded, the items that most often failed a 2007 Ford Transit Connect at the first attempt were Drive shaft joints and boots (front) (19.0%), Suspension mounting area (rear) (16.3%) and Individual sidelight or tail light (front) (11.8%), each as a share of the year's failed first attempts. That is what goes wrong most often on the car. The common faults table shows a different measure: faults that are unusual compared with similar cars.
Among failed first-attempt tests we highlight patterns that appear more often than on similar cars. Top example: Seat belt mounting area (front) (8.4% of those tests; 257 observed failures; about 13× more often than similar cars). These are statistical signals, not a diagnosis of any individual car.
Seat belt mounting area (front) shows up more often than on similar cars (8.4% of those tests; 257 observed failures; about 13× more often than similar cars). That does not prove a design fault. Age, mileage, and how the car was used still matter. Treat it as a pre-purchase checkpoint, not a manufacturer service bulletin.
Common MOT problem areas for the 2007 Ford Transit Connect include Seat belt mounting area (front), Vehicle structure condition (rear), Chassis condition (rear). These are the faults that stand out compared with similar cars, not a complete list of what can go wrong on any individual car.
Advisories flag issues noted at the test and are not a fail rate. We show advisory patterns that appear more often than on similar cars among failed first-attempt tests, separate from common failure rows. Use them as early-warning checks, not as a pass/fail score.
This page highlights MOT failure patterns for the 2007 Ford Transit Connect (registration year) using UK DVSA open data for the selected test year. Patterns are compared with cars of a similar age and mileage. It is a buyer checklist from MOT defect statistics, not a full service history or manufacturer service-bulletin list.
No. MOT tests do not cover engine internals, gearboxes, or many electronic modules. Patterns here come from MOT defect statistics only and should not be read as engine or gearbox reliability scores.

About this data

How this page is built and what it can (and can't) say.

These figures come from UK MOT open data for this model year. We surface common failure patterns against similar cars, not a full reliability score, and not a pass/fail verdict on any individual vehicle.

2024 2025

What we include

UK Class 4 cars only. Normal MOT tests (not retests); first test per vehicle per calendar year; results pass, PRS, or fail.

Same-day repairs

PRS means the car failed items that were fixed at the test station and then passed the same day. We count PRS as a first-attempt fail in headline rates so same-day repairs do not hide problems.

How we compare

We compare this model year with other Class 4 cars of similar age and mileage in the same test year. This model family is left out of the peer group so the car is not measured against itself.

What this does not cover

  • MOTs do not cover engine internals, gearboxes, or many electronics; this is not a full reliability score.
  • Common faults come from MOT defect stats, not manufacturer TSBs or recalls.
  • Age and mileage matching reduces, but does not remove, differences in how cars were used and maintained.
  • If the data for a car is too thin to say anything useful, we say so rather than guess.

Contains public sector information licensed under the Open Government Licence v3.0.

Check any vehicle’s MOT history

Full MOT history, mileage records, and reliability insights for any UK vehicle.

Run a free check